[Vegard]

Going to have a peek in the manual at work, got to be prepared :

[Bushwood Bill]

Originally Posted by Vegard

Going to have a peek in the manual at work, got to be prepared :

Nice! I have mine setup the same way. I prefer using a reg/on-off setup that way I can use whatever tank I want no matter the output pressure.

[SithKnightBB]

Originally Posted by p8ntballr68059

I use a crossy lp and it works great. You can turn the front of the hpr on the asa out a little to allow you to get 200 psi with tank screwed in all the way. It should be the piece that is a different color on the asa.

Tried that with my tanks. You can unscrew it a long way out surprisingly. I went as far as half of the oring showing on the knob. Still couldn't get it down with the tank all the way in.

I'm going to try a few more tricks, I'm going to try to borrow another type of lp tank and trouble shoot from there.

Vegard let me know about the ninja pro. I may go that route if you can you the hoseless hpr with it.

[p8ntballr68059]

I have a ninja reg tank coming in soon I will let you know how it goes

[excope]

Hey P8nt, my old gal treating you ok. I kind of miss her a little. Did you get the back story on why the trigger is gold?

Ex.

[p8ntballr68059]

Originally Posted by excope

Hey P8nt, my old gal treating you ok. I kind of miss her a little. Did you get the back story on why the trigger is gold?

Ex.

No I didn't get the back story enlighten me please. Do you have a black trigger

[excope]

No I don't, it never had one. I'll send you a PM with the back story on it.

[p8ntballr68059]

Good Cuz I'm curious..
Side note lurker barrel and zr1 =ghost farts for sound

[excope]

True that, that is how I ran it as well. I also ran it with a BL cam drive and 360 reg. When I had it I had some tank reg ping and got rid of it by using a hp tank reg but had to use the 360 to go that route. Bob's gloss black almost matches perfect to the black on the ZR1.

[p8ntballr68059]

So does MacDev with the match stik kit I picked up for it before I got my lurker

[Zbarlow]

Having lots of problems guys.

I got a zr-1 with 1.5 bolt. The guy that sent it to me said there was a tiny leak to the bolt. When I got it, aired it up with a ninja reg tank set at 450 psi, air it up, it leaks very badly down through the bolt. I know it is inside the bolt because when I put my finger down the breach I can stop the leak sound by placing my finger over one of the three cut holes in the bolt tip. So it is not sealing inside the chamber of the green bolt sleeve, and the rod like bolt body. Changed Orings, no change, lubed, no change.

Next I come to find out that the reg bonnet is bent on the connector of the reg to the ASA. I mean by the disk like part on the very tip of the Reg on the bottle. Was able to bend it back to plain, but it still leaks from the connection of the bottle and ASA. Not from any of the ASA vent holes or the front of the ASA, but from the connection.

What should I do?

[p8ntballr68059]

hmmm i would say check to make sure the lpr... back cap to the bolt isn't too high also what is the hpr set to .. they are finicky with the pressures a little bit.. for the reg thing contact ninja they can send you a new bonnet for cheap usually.

[Zbarlow]

I don't have a pressure tester, and I hope I didn't ruin anything but from the setting he had it, I adjust the hpr out and back a couple turns to see if that helped, and the lpr I did the same.

I don't think there is a seal that I could have blown cuz it isn't leaking from the frame or anything.

Do you happen to know what the size of the oring on the bolt tip is on the 1.5 bolt?

[p8ntballr68059]

should be the same size as the stock ... see picture above that i posted the other day
when you turned the pressures down did it stop the leak

[Zbarlow]

Nope, leak was consistant no matter what pressure I set it to.

I probably do have the wrong oring. I think I have a size 7/70 in there now.

[p8ntballr68059]

hmmm i would say you need to check the oring and take apart the lpr and see if there is something that needs to be changed in there. there isn't that much that can go wrong with a marker like this

[Zbarlow]

Ok. I will take a look. Thank you very much. I found 8/90 Orings online. I'm gonna try to find them in a store somewhere. Have you or anyone had luck with any particular store for Orings?

[p8ntballr68059]

oring monkey is the best.. also pick up some monkey poo lube it is in my opinion the best lube on the market... plus you smell bananas when you shoot

[Vegard]

www.oringmonkey.com

Print their sizing chart aswell

[p8ntballr68059]

i prefer to hand custom fit my orings to get best performance

[Vegard]

Unless there's unatural amounts of drag or o-rings not sealing, handfitting is a waste of time for the average baller.