Official Vanguard Creed Certified Tech thread!! (TECH QUESTIONS ONLY PLEASE)

AndreAlv · 12-22-2012, 03:32 AM

Cant find serial number om my Demon 2013. In the menus, under info it says (unset) next to serial number! Please help.

WildWayz · 12-22-2012, 04:18 AM

You need to send your board back to Vanguard to be flashed. It looks like it hasn't had the latest software put on it, or a serial number.

AndreAlv · 12-22-2012, 05:03 AM

Quote:

Originally Posted by WildWayz

You need to send your board back to Vanguard to be flashed. It looks like it hasn't had the latest software put on it, or a serial number.

How shall I contact them? I have tried to send mail but no response in weeks.

WildWayz · 12-22-2012, 05:12 AM

Quote:

Originally Posted by AndreAlv

How shall I contact them? I have tried to send mail but no response in weeks.

Contact Frank (think he said in a thread further down, he is back next week) or your local Vanguard repair center.
I am not sure if Reaper can flash them or if they'd just swap it straight out.

Tman201 · 01-01-2013, 02:42 AM

Okay so I just got a new board for my creed and a battery. I charged it up a little and it was shooting good except the screen was super dim. I plugged it in over night to charge and now it won't do anything. I've tried the reset and nothing happens. What you guys think?

ralph0s · 01-01-2013, 07:52 PM

My demon leaks from the top of my grip frame really bad when I first run air through it. When I shoot it once the leak gets way quieter. I checked my bolt guide o-rings they seem fine. Is it my solenoid?

ralph0s · 01-01-2013, 07:56 PM

its a 2012 demon btw dont know if it makes a difference

xmc1146 · 01-01-2013, 09:14 PM

its does because your QEV might be bad.

ralph0s · 01-02-2013, 10:43 PM

Put a new diaphram still does it. Just going to send to deadbox since he fixes vanguards in my region.

tegan765 · 01-11-2013, 06:23 PM

I have a 2012 demon with supposedly 2013 internals. I need help from somebody because I've searched high and low for a number for a tech of someone to fix my gun. Gun started leaking through grip frame so I took the frame off and there was this round solid rubber round piece with a tip on it wedged in the corner of the internals torn almost in half. I checked solenoid gasket, orings ect everything was fine. Went to put it back together then aired it up and gun shot as soon as I aired it up (so I figured that little rubber round piece was like a PVC in the geos so it does shoot when aired up) so I aired it up still leaked I dry fired it and all it made is these puffing sounds so I took it back apart to see if I could find were that rubber piece would go, no luck.... So when I put it back together I pinched the solenoid wires which I'm always careful about with every gun I ever owned but just my frustrated luck pop pinched the solenoid wires and broke one of em. So now I'm pissed because with a company pushing out guns over 1,000$ and no help when things go wrong. So vanguard please help me out with a tech and get my gun back on the field. Please

tegan765 · 01-11-2013, 06:24 PM

I know this is a creed thread I'm just trying to find some help

Pr1m0 · 01-11-2013, 07:50 PM

Deadboxsports.com

Btw

Tht little rubber thing sounds like the qev. Which means its not 13 jnternals

tegan765 · 01-11-2013, 07:54 PM

Were did that thing even go? Lol I can't figure it out

juggernaught_lives · 01-12-2013, 01:06 AM

Quote:

Originally Posted by tegan765

Were did that thing even go? Lol I can't figure it out

2012 Bolt, Can and Manifold

2013 Bolt, Can and Manifold

Hope this helps
The following is for a 2012 Manifold help and walk through.

If this is not what you're talking about then post a pic of your issue

tegan765 · 01-12-2013, 04:48 AM

Wow thanks man!! I appreciate everything

DaEck · 01-13-2013, 05:33 PM

Just picked up a 2012 demon and gassed it up and it is leaking very loud out of The rear screw area never had a non macro gun help!

juggernaught_lives · 01-13-2013, 06:36 PM

Quote:

Originally Posted by DaEck

Just picked up a 2012 demon and gassed it up and it is leaking very loud out of The rear screw area never had a non macro gun help!

Remove the Frame check the Transfer Tube, make sure it has the orings on it also make sure the screws holding down the manifold are not loose.

Get back to me if this worked out.

trainor · 01-19-2013, 01:06 PM

Im getting a 2013 demon and was wondering if i should use my normal ninja reg or would a slp work better?

juggernaught_lives · 01-19-2013, 01:31 PM

Quote:

Originally Posted by trainor

Im getting a 2013 demon and was wondering if i should use my normal ninja reg or would a slp work better?

I would say try it, if you experience drop off switch to a standard LP reg 450-550. Most standard Ninja Regs will do this with no problem.

I have been using an SLP on my Demon with no issues. But it varies from marker to marker. Set Up, Maintenance and Settings all play a factor.

WildWayz · 01-19-2013, 01:32 PM

Personally, I wouldnt risk it. As Jugs said, varies from marker to marker.
Stick to LP or MP and don't worry.

dpmielech · 02-18-2013, 05:23 PM

i just picked up a brand new creed. just a few questions, i havent done much messing with the gun yet but i just played this past weekend. im looking for a tuning guide for the creed and cant seem to find one. trying to make a little more quiet because it has a lot of kick and is quite loud. i was also chopping some balls as well and thought that might be the issue. also want to know what type of upgrades are available for the gun, and anything else that you think a new creed owner needs to know. Thanks!