[bunkerking_13]

Im assuming better durability with ever so slightly less drag.

[soflaballer954]

I started my own thread, I assume boss is busy so ill ask here. I have a boss bolt xsv and I'm shooting it with the long spring 5 dwell and a 679 freak. I'm getting 295 293 but then after shooting a rope or two I get 260 263 265. I'm using a HP tank and its really confusing me as to why this is happening. It's 1.5 turns out.

[ncstatered21]

Originally Posted by soflaballer954

I started my own thread, I assume boss is busy so ill ask here. I have a boss bolt xsv and I'm shooting it with the long spring 5 dwell and a 679 freak. I'm getting 295 293 but then after shooting a rope or two I get 260 263 265. I'm using a HP tank and its really confusing me as to why this is happening. It's 1.5 turns out.

Try the recommended settings with short spring and see what u get.

Btw I put the orings on yesterday. They look sweet.

[polabear]

Try the recommended settings with short spring and see what u get.

Btw I put the orings on yesterday. They look sweet.

Keep us updated on thoes bolt sail orings. Me likley likley

[soflaballer954]

Originally Posted by ncstatered21

Try the recommended settings with short spring and see what u get.

Btw I put the orings on yesterday. They look sweet.

Will do. Now that I think about it, it wasn't till I changed springs that I started running into problems. I'm not 100% but I think so...ill try. So are the settings different than what boss recommends for the each individual spring? I was told to underbore and I did. And I also recall having the stock barrel and it wasn't giving me as many problems and after going from the stock to 679 I didn't see a big difference in fps.

[Kazer]

Out of curiosity, how old is your tank regulator / how broken in is your Axe? Ballpark amount of cases through it would suffice. Reason I ask is it's possible this is a recharge rate issue.

[ncstatered21]

Originally Posted by soflaballer954

Will do. Now that I think about it, it wasn't till I changed springs that I started running into problems. I'm not 100% but I think so...ill try. So are the settings different than what boss recommends for the each individual spring? I was told to underbore and I did. And I also recall having the stock barrel and it wasn't giving me as many problems and after going from the stock to 679 I didn't see a big difference in fps.

Underboring should give you more consistency. Try short spring, 140 psi, 3 dwell, 1 1/2 out on backcap. Those are his recommended starting settings that come with a new bolt.

I'm getting really inconsistent numbers with mine and I hope it's not cause of the reg but we will see.

I was getting like 260-265 the other night now I'm getting 310-315. I'm gonna turn down pressure a hair and hopefully can get it in 285-290 range.

If it keeps being inconsistent I may have to figure some other things out

[soflaballer954]

Originally Posted by Kazer

Out of curiosity, how old is your tank regulator / how broken in is your Axe? Ballpark amount of cases through it would suffice. Reason I ask is it's possible this is a recharge rate issue.

I got a new reg at cup since the old one was creeping. I noticed a few problems starting then too. And my tank is barely a few months old

Originally Posted by ncstatered21

Underboring should give you more consistency. Try short spring, 140 psi, 3 dwell, 1 1/2 out on backcap. Those are his recommended starting settings that come with a new bolt.

I'm getting really inconsistent numbers with mine and I hope it's not cause of the reg but we will see.

I was getting like 260-265 the other night now I'm getting 310-315. I'm gonna turn down pressure a hair and hopefully can get it in 285-290 range.

If it keeps being inconsistent I may have to figure some other things out

Like I said I'm under boring paint

And putting the reg at 140 (even though I think the recommended are 150) would give me really low numbers.


I'm having to go to almost 180 now. -_-

[ncstatered21]

Originally Posted by soflaballer954

I got a new reg at cup since the old one was creeping. I noticed a few problems starting then too. And my tank is barely a few months old

Like I said I'm under boring paint

And putting the reg at 140 (even though I think the recommended are 150) would give me really low numbers.

I'm having to go to almost 180 now. -_-

What kind of orings do you have on the bolt guide?

I had a similar issue with the lurker bolt. What is your poppet like? Make sure it is all the way in and lubed.

[soflaballer954]

I have the xsv bolt so I have the xsv o rings. And what do you mean if my poppits is all the way in?

[ncstatered21]

Originally Posted by soflaballer954

I have the xsv bolt so I have the xsv o rings. And what do you mean if my poppits is all the way in?

I more meant make sure it isn't damaged and makes a good seal.

Mainly make sure it is lubed nicely.

[soflaballer954]

Ill check soon. And I lube it after every weekend

[ncstatered21]

Originally Posted by soflaballer954

Ill check soon. And I lube it after every weekend

Good stuff.

BTW Go Pirates! See you in the Big East!

I would ask you what tournaments y'all are playing this year but that would get the thread off topic haha.

[soflaballer954]

Originally Posted by ncstatered21

Good stuff.

BTW Go Pirates! See you in the Big East!

I would ask you what tournaments y'all are playing this year but that would get the thread off topic haha.

Lol! We will see you in the big east buddy good luck. And yeahhhh it would. I'm actually an alumni but there's a Ucf FB page. My old roommate is the president and they're officially a school organization now. But I'll be at nationals with FAU .

[ncstatered21]

Originally Posted by soflaballer954

Lol! We will see you in the big east buddy good luck. And yeahhhh it would. I'm actually an alumni but there's a Ucf FB page. My old roommate is the president and they're officially a school organization now. But I'll be at nationals with FAU .

I should be at nationals barring anything unforseen. Hmu if you want and I'll maybe see u there!

My cousin goes to UCF. I think he is a student athletic trainer for the football team.

[bunkerking_13]

Got them on the guide today. They are aesthetically pleasing.

image-935496117.jpg

[ncstatered21]

Originally Posted by bunkerking_13

Got them on the guide today. They are aesthetically pleasing.

Attachment 55582

I was about to post my pictures as well but you beat me to it. They are quite pleasing!

EDIT: I'll put it up anyways haha

[polabear]

that is sexy!

[bunkerking_13]

Am I the only one who wishes someone would produce a higher quality grip for the Axe? I cant stand the fact that my grips can be pushed in and don't sit flush with the frame. I really miss the feel of my UL frame grips, and the sticky grips. If Boss or someone could produce a soft, thick, legit grip for say <$25ish, I would absolutely purchase them. Nothing fancy, just simple, sticky, solid grips. I think my Axe would be much more comfortable. Anytime you can improve the ergonomics of an Axe, I think it should be done.

Also, I cannot stand the plasticy 2 piece panels that companies already produce as far as after market grip panels. Hate them. One piece ftw.

[soflaballer954]

Originally Posted by bunkerking_13

Am I the only one who wishes someone would produce a higher quality grip for the Axe? I cant stand the fact that my grips can be pushed in and don't sit flush with the frame. I really miss the feel of my UL frame grips, and the sticky grips. If Boss or someone could produce a soft, thick, legit grip for say <$25ish, I would absolutely purchase them. Nothing fancy, just simple, sticky, solid grips. I think my Axe would be much more comfortable. Anytime you can improve the ergonomics of an Axe, I think it should be done.

Also, I cannot stand the plasticy 2 piece panels that companies already produce as far as after market grip panels. Hate them. One piece ftw.

This! I would also purchase some.

[Kazer]

Wash your grips with a small drop of dish soap and warm water.