 |
|
05-20-2012, 04:30 PM
|
#106
|
|
Get Em Out.
|
vic question
I converted my pmi reactor tank to low pressure and played today I have supercharged Vic and a 65/190 setting my balls were dropping off down field causing me to aim high...it was shooting down slightly in ramp and I take care of it ie. Clean,lube etc. I had to turn my dwell to 10 from 8 for better results... any ideas? I know there's a longer front reg or Mabey try a different tank low pressure reg? Thanks..
__________________
Ballin.
|
|
|
|
05-22-2012, 09:41 AM
|
#107
|
|
P4 Paintball Products
Join Date: Jun 2011
Location: Hershey, PA
|
Put your dwell back to 8 and up your Lpr to 75. Then adjust the hpr accordingly to pass chrono
|
|
|
|
|
05-28-2012, 08:39 PM
|
#108
|
|
Get Em Out.
|
My pmi converted low pressure tank was starving my gun in ramp I had to go to a ninja slp reg to solve the issue thank you and hope this helps anyone else.
__________________
Ballin.
|
|
|
|
|
05-28-2012, 10:17 PM
|
#109
|
|
|
Alright I been using my bob long ripper for little over 2 months, I've done all the maintanence for lubricating the engine HPR and LPR. I've taken this gun apart numous times. I can't seem to get it to shoot above 260. My current settings are 80LPR and 200HPR. I have the SC engine, I've been using the pressure tester to gauge it. My friend has a victory v2 with the same settings and shooting 285+. Need some help on my situation please.
|
|
|
|
|
06-01-2012, 07:54 PM
|
#110
|
|
Get Em Out.
|
What's your dwell at
__________________
Ballin.
|
|
|
|
|
06-02-2012, 01:19 AM
|
#111
|
|
|
Dwell is stock 6ms, I bumped mine to 8ms.
|
|
|
|
|
07-01-2012, 01:35 PM
|
#112
|
|
|
how important is the dwell on 100+ degree days? do i raise or lower it? i couldnt get chronoed above 260 today
__________________
Joshua Davis
UNITEDCLOTHINGCOMPANY.COM
US AIR FORCE/AIR GUARD
Bob Long RIPPER
|
|
|
|
|
08-19-2012, 05:08 PM
|
#113
|
|
Join Date: Nov 2010
Location: Plymouth
|
what should i do if my gun will shoot, but once it gets going it will just dump all the air and paint out of the barrel and the asa..... adjust the lpr? or the debounce?
__________________
Mass Mayhem Paintball
|
|
|
|
|
08-19-2012, 05:25 PM
|
#114
|
|
Read the manual!!
Join Date: Dec 2005
Location: OK
|
Quote:
Originally Posted by mclines
what should i do if my gun will shoot, but once it gets going it will just dump all the air and paint out of the barrel and the asa..... adjust the lpr? or the debounce?
|
It's valve float issues. |
|
|
|
|
08-20-2012, 08:47 AM
|
#115
|
|
|
I am getting a V1 and looked at a manual and it did not give any info or unless I missed it.
Apparently it is the stock board what board is stock ?
It is supercharged.
You enter programming mode by holding the trigger then turn it on. What color do the lights mean ?
I'll put it at default settings. But what are the default settings ? How do I change firing modes ? i play and practice in psp mode.
Would appreciate some schooling on the V1 thanks in advance.
Sonny
|
|
|
|
|
08-20-2012, 12:45 PM
|
#116
|
|
Read the manual!!
Join Date: Dec 2005
Location: OK
|
M8/Ryujin board manual is what you need.
|
|
|
|
|
08-20-2012, 11:34 PM
|
#117
|
|
|
Quote:
Originally Posted by gamer565
M8/Ryujin board manual is what you need.
|
Thank you. |
|
|
|
|
11-25-2012, 09:29 PM
|
#118
|
|
PRBALLER
Join Date: Jan 2005
Location: area code 787
|
Quote:
Originally Posted by pttlwin
Hey Guys
just got a v2 vic off nation and i kinda found some wear on the poppet. Just want to know if this is usual or something I need to worry about? Should I call bob long and ask about replacement?
 |
I have this same problem, any one knows why this happens?
thanks in advance |
|
|
|
|
11-25-2012, 11:18 PM
|
#119
|
|
Read the manual!!
Join Date: Dec 2005
Location: OK
|
It's just where the spring has been rubbing, it's nothing to worry about.
|
|
|
|
|
03-26-2013, 07:42 PM
|
#120
|
|
|
I am trying to equip a few guns with PSP mode, 12.5 BPS. The guns are two Victory and one Closer. All have 4C eyes with Ryujin board. Followed instructions, set white LED to setting 3 (PSP autoresponse) and teal LED to setting 6 (12.5 BPS).
Gun cycles as it should in test mode, eyes off. Same when air is added. When paint is added, eyes on, they all seem to go back into semi, or what seems to be semi. Any help would be appreciated as we have a tournament on Saturday.
|
|
|
|
|
04-12-2013, 09:01 PM
|
#121
|
|
|
Quote:
Originally Posted by sargoodwin
I am trying to equip a few guns with PSP mode, 12.5 BPS. The guns are two Victory and one Closer. All have 4C eyes with Ryujin board. Followed instructions, set white LED to setting 3 (PSP autoresponse) and teal LED to setting 6 (12.5 BPS).
Gun cycles as it should in test mode, eyes off. Same when air is added. When paint is added, eyes on, they all seem to go back into semi, or what seems to be semi. Any help would be appreciated as we have a tournament on Saturday.
|
you have it in the wrong setting psp auto response gives you a shot for every trigger pull and release basically a semi mode that helps you reach whatever bps you want to shoot without ramping. to ramp set it to setting 5 psp 100% ramping |
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
