[dehr]

Originally Posted by p8ntballr68059

be honest you are gonna use a lot of ky and tissues

nah, i have zach's sister for that


got this odd PM this morning lol

Originally Posted by cdrdr

well everytime i slide into bunkers the buttons come undone would you happen to have a 3xl pants or know someone who has them? i bought these brand new 140$ and wore them for five minutes idk why they come undone i tried adjusting all straps but see..there already really big in length and width in legs its just waist size so i figure i need a 3XL..any ideas?

[p8ntballr68059]

wtf i think he is trying to get into your pants dave

[dehr]

idont even know this dude. just got this out of nowhere

[Shooter28]

Originally Posted by UNDRPRVLGD_V2

So this season I played 15 events. 8 nationals events.

Went from a 450 APPA score to a almost 900 APPA score.

I've been chilling at 667 for a while. That's a ton of events tho

[memoon]

Originally Posted by deadly*

guys, isnt there a machinist on pbn that can bore out barrels to fit freak inserts?

do any of you guys happen to know his username?

Look up super stanchy customs on Facebook

[americanidiot748]

does anyone know what type of 15* VAs were released for the SFT?

NDZ
Dark
Ton Ton

any others?

EDIT: also i asked earlier about Ego regs on a shocker, will a 06 ego reg work? (i'm asking specifically about that one because i found one for 23 shipped...)

[godraep]

I have never seen anything that looks good come from Super stanky customs. All of his work looks subpar and unfinished.

[memoon]

Originally Posted by godraep

I have never seen anything that looks good come from Super stanky customs. All of his work looks subpar and unfinished.

Well have to agree to disagree on that. The work I've seen in person looks very well done

[p8ntballr68059]

Originally Posted by americanidiot748

does anyone know what type of 15* VAs were released for the SFT?

NDZ
Dark
Ton Ton

any others?

EDIT: also i asked earlier about Ego regs on a shocker, will a 06 ego reg work? (i'm asking specifically about that one because i found one for 23 shipped...)

the ego 6 reg will fit just fine on a shocker they take standard threads

Originally Posted by godraep

I have never seen anything that looks good come from Super stanky customs. All of his work looks subpar and unfinished.

i kinda agree to an extent he has done some decent things in the past

[americanidiot748]

i wasn't worried about "fit" so much as will the reg be able to lower the OP low enough for the shocker...

[Umami]

Originally Posted by Umami

See avatar. They sell the SL3 with an LP spring (as used in the Geo) if you contact them and request it.

.

[p8ntballr68059]

Originally Posted by americanidiot748

i wasn't worried about "fit" so much as will the reg be able to lower the OP low enough for the shocker...

you should have no problems with that the ego runs at a lower pressure than the shocker to start with usually

[smartballer91]

Originally Posted by americanidiot748

does anyone know what type of 15* VAs were released for the SFT?

NDZ
Dark
Ton Ton

any others?

EDIT: also i asked earlier about Ego regs on a shocker, will a 06 ego reg work? (i'm asking specifically about that one because i found one for 23 shipped...)

ndz is 15*
hybrid 15*
ton ton is a 15*
dark is a 10*

Those should be all of them for sfts.

[americanidiot748]

Originally Posted by Umami

.

you mentioned the SL3 reg but i didn't think the stock 06 Ego reg was an SL3 or if they were the same...

Originally Posted by p8ntballr68059

you should have no problems with that the ego runs at a lower pressure than the shocker to start with usually

Really? i was under the impression the OP on an Ego was about 300ish

[p8ntballr68059]

the ego 5 ran about 180 psi to 200 psi

[southerndandy]

Originally Posted by godraep

I have never seen anything that looks good come from Super stanky customs. All of his work looks subpar and unfinished.

i had him mill out the barrel on my phantom to take freak inserts and i've had no issues with it at all. the inserts fit pretty much perfectly. as far a looking finished, the section he milled wasn't re-polished or anything, but then again it doesn't need to be because freak inserts go in it now.

[p8ntballr68059]

so what barrel do you guys suggest i get for my zr1 i know the stock barrel is great but i want a smaller bore

[UNDRPRVLGD_V2 (Banned)]

Originally Posted by Shooter28

I've been chilling at 667 for a while. That's a ton of events tho

Just wanting to make pro man, grinding and trying to get noticed.

[deadly*]

I don't want to knock on lurker cause i know he knows what hes doing but is the bolt really going to be THAT good for us shocker owners? Or is it because it came from Lurker and all the wait thats been around for it that everyone BELIEVES its gonna be this awesome bolt...

Again, I love lurkers stuff I just wanna see someone test it!

[p8ntballr68059]

that is kinda where im at i wanted to see some testing of the finished product before it went on sale

[smartballer91]

Its going to be good for us shocker owners. Its not hype. Otherwise that'd be a waste of money. And I don't waste money.