Help! Invert mini problems!!!!

ankurpatel360 · 07-02-2011, 03:37 PM

Ok so when I went to the chrono station the paintballs would either go 2 feet or get stuck in the barrel. I replaced the battery and used my friends tank and single feed it and it still have the problem.all of the o rings look fine on the bolt. Should I replace all of them? Sorry this is my first electronic marker

Ken448 · 07-02-2011, 04:38 PM

check pressure, then check rear of the bolt assembly. The further you screw it out, the move velocity you will get. None of those work, check dwell (read manual for details)

ankurpatel360 · 07-02-2011, 09:48 PM

Someone at the field told it it was something with my bolt

Razyger · 07-03-2011, 06:35 AM

How easily does your bolt slide along the bolt guide?

sokrphenom · 07-03-2011, 03:08 PM

Check the reg. to make sure the pressure is high enough too. If the marker has been take apart maybe the check valve fell out.

vesparider · 07-03-2011, 08:51 PM

Lubrication is your friend...

xParkerx386 · 07-08-2011, 07:39 PM

yeah if its new the company screws it in all the way and it doesnt shoot try unscrewing it then shoot it should work

SpeedBallDEVIL · 07-09-2011, 10:49 PM

First you want to make sure your input pressure is sitting around 160-200 PSI, no more than 200 PSI though. To adjust that there is a set screw on the front of your regulator, turning it in increases the input pressure, turning it out decreases.

Next you move on to your velocity adjustments. Turn the back cap all the way in and then back it out 3/4 to 1 full turn. This is also called resetting the poppet. To fine adjust your FPS, simply back out the back cap in small increments until the desired pressure is reached.

Okay, if those two things don't work, something is wrong with the gun mechanically. First you want to relubricate your bolt guide assembly. Wipe all remaining lube off and replace it with a nice thin coating.

If this doesn't work. The oring directly related to the velocity is the poppet oring. Replace this and that should do the trick.

IF THAT DOESN'T WORK, just PM me lol.

Hope this helps,
-Ryan

ish singh · 11-11-2012, 05:06 PM

HELP!!! I bought a new Empire Mini version 3 paintball gun and i went to play. it worked finw but when i got home, i tried to take out the bolt from the feedneck and i heard a LOUD popping noise and the bolt came out... the regulator gage said 0.... what could bbe the problem and now the bolt wont fit all the way in. please reply thank you

Cromer611 · 11-12-2012, 02:28 AM

Quote:

Originally Posted by ish singh

HELP!!! I bought a new Empire Mini version 3 paintball gun and i went to play. it worked finw but when i got home, i tried to take out the bolt from the feedneck and i heard a LOUD popping noise and the bolt came out... the regulator gage said 0.... what could bbe the problem and now the bolt wont fit all the way in. please reply thank you

Wtf what? You tried to take the bolt out the feed neck?

Christian P · 11-12-2012, 06:55 AM

Quote:

Originally Posted by ish singh

HELP!!! I bought a new Empire Mini version 3 paintball gun and i went to play. it worked finw but when i got home, i tried to take out the bolt from the feedneck and i heard a LOUD popping noise and the bolt came out... the regulator gage said 0.... what could bbe the problem and now the bolt wont fit all the way in. please reply thank you

Did you line up the back of the bolt assembly so the hole on the back of the poppet fits into the nub that sticks out of the back of the market frame? I thought mine had issues before I noticed it needed to fit in right.

fox5100 · 11-15-2012, 07:58 AM

Did you try resetting the board to factory?

fox5100 · 11-15-2012, 08:00 AM

Quote:

Originally Posted by ish singh

HELP!!! I bought a new Empire Mini version 3 paintball gun and i went to play. it worked finw but when i got home, i tried to take out the bolt from the feedneck and i heard a LOUD popping noise and the bolt came out... the regulator gage said 0.... what could bbe the problem and now the bolt wont fit all the way in. please reply thank you

Are you being serious?

Blak Katalyst · 11-16-2012, 04:33 PM

Quote:

Originally Posted by Cromer611

Wtf what? You tried to take the bolt out the feed neck?

What? You don't?

2pipes · 11-17-2012, 05:09 PM

Quote:

Originally Posted by ish singh

HELP!!! I bought a new Empire Mini version 3 paintball gun and i went to play. it worked finw but when i got home, i tried to take out the bolt from the feedneck and i heard a LOUD popping noise and the bolt came out... the regulator gage said 0.... what could bbe the problem and now the bolt wont fit all the way in. please reply thank you

Please tell me you meant to say " from the rear of the marker". Look at your manual did all the pieces come out? The bolt guide, bolt, and the spring should have come out together. Is it possible the spring is still in the marker?