[MiDWeST KiD]

yeah I tryed raising the sensitivity and it doesnt do anything. and I dont think its the board because I just shot this gun literally on thursday and there was not a prob and now its doing this. On saturday I took the gun apart and cleaned it and then tryed to shoot it later on saturday and it just does this. anything else?

[MiDWeST KiD]

Also could you list all the stock settings are supposed to be set at as well and any other ideas you have. Thank you for trying to help me. I really appreciate it

[WildWayz]

Here are the out of the box settings for the Creed:

Dwell 12
debounce 5.0
eye delay 3.0
eye sens 10
bolt delay 8.0
FSDO dwell 1.0
Loader pulse 20

[MiDWeST KiD]

any help guys?

[WildWayz]

When aired up, is there pressure to the bolt - ie can you push it forward and it resists or is it 'sloppy'?

Have you got the regs set up correctly?


If that is all ok and you are getting an error when the eyes are off, as mentioned it could be a board issue. Could have been some paint/water get onto it and shorted something out.

[Reaper (ACI)]

Try a factory reset on the board. Take the grips off and lift the battery, there I a small button under the battery. That's the reset button.

If that doesn't fix it, send it in.

[MiDWeST KiD]

im going to try it and ill see if it works. ill let you know

[WildWayz]

Also, make sure there is deffo no gunk on the eyes or the eye holes.

[MiDWeST KiD]

yeah I cleaned them last night

[MiDWeST KiD]

alright gun is working now. thank you guys for all the help. I really apprieciate it.

[choops182]

leaking down the barrel, is the poppet o ring the only thing it can be ?

[WildWayz]

Yes, it will be one of the valve orings - probably the outer ones.

[beastmar]

Is my board fried? I have 2 vanguard creeds and when I tried to plug one of them in to charge, nothing came up on the screen. I used the other charged battery and put it in the non working screen one and it does not turn on. It was working fine last week and now all of a sudden goes dead... Could it be a board issue? Is there anyway to diagnose this? Maybe a reset?

[Reaper (ACI)]

If you put a fresh charged battery in, it's likely the board. You can try the factory reset. Button is on the board behind the battery.

[beastmar]

Originally Posted by Reaper (ACI)

If you put a fresh charged battery in, it's likely the board. You can try the factory reset. Button is on the board behind the battery.

Oh darn. The factory reset did not solve my issue. I haven't had the creed for that long and the board decides to go capoot...I wonder why? What could cause the board to fail? It worked last weekend... I've never used my creed in the rain and even then my old angel board which is a lot older than most still runs like a champ. It's going to be tough to shell out that kind of cash on a new board.

[BXLNT]

.

[MR HAZARDOUS123]

I lost the feedneck lever and hardware can someone tell me where to order or a number to call vanguard.

[overweightangel275]

Anyone of the service centers should be able to help you out. I'm on the east coast closest to you.

www.vanguardpaintballusane.com

[a1exweibl]

I have a demon that when I try and shoot it will cycle but only putter and not give me a full shot, what could this be?

[overweightangel275]

Probably the qev. What's the serial number? Have you lubed everything correctly?

[joshnielson]

My gun was chopping and inconsistent found out my eyes were bad replaced then i rebuilt everything on the now it wont shoot at all any advice also made sure everything went baxk in so it has all its pieces and i followed the creed manual