Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 09-23-2012, 01:31 PM #1
NoobWithAnAttitude
Becoming Less of a Noob
 
NoobWithAnAttitude's Avatar
 
Join Date: Sep 2012
Problems with balls rolling out of barrel on a Trilogy Pro

I bought a used trilogy pro autococker and it works great aside from balls keep rolling out of the barrel because the bolt is hitting it so hard. The guy there said that it could be the pressure is too high or the barrel bore could be too large please help.

Last edited by NoobWithAnAttitude : 09-23-2012 at 01:54 PM.
NoobWithAnAttitude is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 09-23-2012, 02:06 PM #2
sucka T.
 
 
sucka T.'s Avatar
 
Join Date: Nov 2003
Location: GA
 has been a member for 10 years
do you have a barrel kit? i would suggest a barrel kit with different bore sizes to get a better paint to bore match
__________________
1st Annual ST Friendship BBQ

ThreadSavers®

http://www.ohnoes.org/

http://www.pbnation.com/showthread.p...hreadid=891102
sucka T. is offline   Reply With Quote
Old 09-23-2012, 02:07 PM #3
Lawpass
 
 
Lawpass's Avatar
 
Join Date: Jul 2009
Location: MA
Lawpass has achieved Level 1 in PbNation Pursuit
It's probably just that the stock barrel is too large for the paint. You need the inside diameter of the barrel to be slightly smaller to prevent rollouts (look up underbore). You can either use a small bit of electrical tape on the back, or pick up a lapco bore sizer, or pick up a smaller bore barrel or barrel kit.
Lawpass is offline   Reply With Quote
Old 09-23-2012, 02:24 PM #4
NoobWithAnAttitude
Becoming Less of a Noob
 
NoobWithAnAttitude's Avatar
 
Join Date: Sep 2012
Ok thanks I'll try that but is there also a chance it could be that the pressure is too high because the back block is really tight when gassed up
NoobWithAnAttitude is offline   Reply With Quote
Old 09-23-2012, 02:52 PM #5
cruciatus111
GOOD NEWS EVERYONE!!!
 
cruciatus111's Avatar
 
Join Date: Mar 2009
Location: Honolulu, Hawaii
cruciatus111 is playing at Living Legends V
cruciatus111 is for the Gunfight
cruciatus111 has achieved Level 2 in PbNation Pursuit
cruciatus111 is attending Decay of Nations VI
? the bolt pushes the ball into the barrel always because it is a closed bolt marker, and if the bore of the barrel is to big, the ball will just roll out
__________________
[̲̅$̲̅(̲̅100̲̅)̲̅$̲̅l
808 all day every day
Pump guns are fun guns
WGP Jeff Orr Blackout #41/60
cruciatus111 is offline   Reply With Quote
Old 09-23-2012, 03:01 PM #6
NoobWithAnAttitude
Becoming Less of a Noob
 
NoobWithAnAttitude's Avatar
 
Join Date: Sep 2012
Ya I know that I just thought maybe the bolt was pushing the balls harder than it should
NoobWithAnAttitude is offline   Reply With Quote
Old 09-23-2012, 05:13 PM #7
Bigjoe11
"The Boss"
 
Bigjoe11's Avatar
 
Join Date: Jun 2011
Location: North Carolina
Bigjoe11 owns a Planet Eclipse Etek
Bigjoe11 has achieved Level 1 in PbNation Pursuit
Bigjoe11 has achieved Level 2 in PbNation Pursuit
Bigjoe11 supports DLX Technology
Having the lpr pressure too high wouldn't puch balls out of the barrel, but it is better to have it lower so if a paintball gets pinched, it doesn't chop.
__________________
-UCP
Bigjoe11 is offline   Reply With Quote
Old 09-23-2012, 05:16 PM #8
Lawpass
 
 
Lawpass's Avatar
 
Join Date: Jul 2009
Location: MA
Lawpass has achieved Level 1 in PbNation Pursuit
It could be, but that really won't have much to do with roll outs. The LPR on the front controls how much air issued to recock the marker (moving the bolt as well), and even from the factory these came set a little higher than they needed to be. If you have some air you can try adjusting this down by unscrewing it off and turning the adjustment screw in slightly to reduce the pressure until it will just recock the marker consistently.
Lawpass is offline   Reply With Quote
Old 09-23-2012, 06:49 PM #9
NoobWithAnAttitude
Becoming Less of a Noob
 
NoobWithAnAttitude's Avatar
 
Join Date: Sep 2012
Ok thanks for the answers. The bore I'm using right now is .687 what size should I get to replace it?
NoobWithAnAttitude is offline   Reply With Quote
Old 09-23-2012, 07:03 PM #10
YellowDart712
 
 
YellowDart712's Avatar
 
Join Date: Oct 2011
Your best bet if you can afford it is to invest in a barrel kit that comes with multiple size inserts. If you are going to be sticking to whatever paint your using now for awhile and don't have the cash for a kit find out what size the paint your using is and maybe a shop at a field near you can sell just the right size barrel to you..

Couldnt tell you what bore size you need because there are a few different sizes of paint. Put the paint in a barrel and if the paintball rolls out without any force the bore size is to big, if it gets stuck in the barrel try to blow it out and it shouldn't take much force if its the right size. If it takes alot then the bore for that barrel is too small.
__________________
I see your freedom, and raise you Merica -KCCO
YellowDart712 is offline   Reply With Quote
Old 09-23-2012, 10:06 PM #11
Tempted (Banned)
 
Join Date: Feb 2010
Location: N Ga
I'm not 100% sure that the OP is aware that there is no ball detent.
Tempted is offline   Reply With Quote
Old 09-24-2012, 02:05 AM #12
Rebel_816
Don't eat that....
 
Rebel_816's Avatar
 
Join Date: Apr 2007
Location: Lynn, AR
if your short on cash and dont want to buy a barrel kit, you can put a little tape on the inside of the barrel like this:



aka the "ghetto widget mod".

you should probably look for a .682 or .684 barrel. but in all honestly you really need a kit for cockers. the paint to bore match is the only thing that holds the ball in place. the detent is just there to prevent double feeds.
__________________
Rapper
Rebel_816 is offline   Reply With Quote
Old 09-24-2012, 10:04 AM #13
NoobWithAnAttitude
Becoming Less of a Noob
 
NoobWithAnAttitude's Avatar
 
Join Date: Sep 2012
Yeah Ill go with the ghetto widget mod until I get a barrel kit
NoobWithAnAttitude is offline   Reply With Quote
Old 09-24-2012, 01:04 PM #14
sucka T.
 
 
sucka T.'s Avatar
 
Join Date: Nov 2003
Location: GA
 has been a member for 10 years
Quote:
Originally Posted by NoobWithAnAttitude View Post
Yeah Ill go with the ghetto widget mod until I get a barrel kit
__________________
1st Annual ST Friendship BBQ

ThreadSavers®

http://www.ohnoes.org/

http://www.pbnation.com/showthread.p...hreadid=891102
sucka T. is offline   Reply With Quote
Old 09-24-2012, 02:06 PM #15
masterofTHUMBS
boom headshot
 
masterofTHUMBS's Avatar
 
Join Date: May 2007
Location: 703
masterofTHUMBS posts videos on PbNation
masterofTHUMBS is an NCPA player
masterofTHUMBS supports Pev's Paintball
masterofTHUMBS plays in the APPA D5 division
ghetto widgets all day, err'y day.

Anytime I think about getting a freak kit, I look over to the roll of tape and forget all about the freak.
masterofTHUMBS is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump