Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 08-02-2012, 04:48 PM #22
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
Did you try a new board or no?
ETH13 is offline   Reply With Quote
Old 08-03-2012, 12:26 AM #23
theblindchicken
49'er
 
theblindchicken's Avatar
 
Join Date: Jun 2011
Location: Long Beach, CA
theblindchicken is an NCPA player
theblindchicken is an NCPA National Champion
theblindchicken plays in the APPA D5 division
Quote:
Originally Posted by ETH13 View Post
what do you mean by it maxing out? just the velocity going all the way up(or down)?
Correct. Once the reg has maxed/zero'd out, the adjustment screw cannot turn any further and should allow the regulator to unscrew itself from the grip frame.
theblindchicken is offline   Reply With Quote
Old 08-03-2012, 10:45 PM #24
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
I got the regulator off by doing what you suggested. I took a different Wrench than the one included and got a little more leverage.
ETH13 is offline   Reply With Quote
Old 08-04-2012, 12:40 AM #25
theblindchicken
49'er
 
theblindchicken's Avatar
 
Join Date: Jun 2011
Location: Long Beach, CA
theblindchicken is an NCPA player
theblindchicken is an NCPA National Champion
theblindchicken plays in the APPA D5 division
Now clean it out using the guide in the ultimate ion guide sticky (check my sig) and reattach (with some lubrication on the threads so you can get it off next time!) test and see if the reg was causing your problem.
theblindchicken is offline   Reply With Quote
Old 08-04-2012, 09:22 AM #26
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
i cant move the velocity adjuster so I can't see the bottom screw.
ETH13 is offline   Reply With Quote
Old 08-06-2012, 12:14 PM #27
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
So I got it apart and cleaned it but now when I shoot it nothing happens at all. The air stays in the gun, I can hear the trigger clicking but nothing happens.
ETH13 is offline   Reply With Quote
Old 08-06-2012, 02:06 PM #28
theblindchicken
49'er
 
theblindchicken's Avatar
 
Join Date: Jun 2011
Location: Long Beach, CA
theblindchicken is an NCPA player
theblindchicken is an NCPA National Champion
theblindchicken plays in the APPA D5 division
Did you make sure to readjust the regulator after your replaced it back on the gun?
theblindchicken is offline   Reply With Quote
Old 08-06-2012, 02:35 PM #29
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
What do you mean?
ETH13 is offline   Reply With Quote
Old 08-06-2012, 10:29 PM #30
ProtoxxPaintball
USAF
 
ProtoxxPaintball's Avatar
 
Join Date: Dec 2005
Location: 941
ProtoxxPaintball donated to help Peyton Trent
ProtoxxPaintball supports our troops
ProtoxxPaintball is an NCPA player
ProtoxxPaintball supports Empire
There is no air going through the regulator. When you took it off using the method you used, you zeroed the reg out meaning no pressure is going past the macrofitting virtually. You need to slowly increase the pressure going through the reg by adjusting the nut on the bottom and increase the pressure to appx. 150 psi.
__________________
Old Feedback +54/-0
NIKON D60 FS PM ME
ProtoxxPaintball is offline   Reply With Quote
Old 08-07-2012, 10:04 PM #31
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
Even though the gauge reads 200 psi when I put air in? I should still loosen the lower screw on the regulator?
ETH13 is offline   Reply With Quote
Old 08-08-2012, 12:38 AM #32
theblindchicken
49'er
 
theblindchicken's Avatar
 
Join Date: Jun 2011
Location: Long Beach, CA
theblindchicken is an NCPA player
theblindchicken is an NCPA National Champion
theblindchicken plays in the APPA D5 division
Your ion's pressure should be operating below 180 psi. If the pressure is too high, the solenoid may not have the power to act against the pressure and fully cycle.
theblindchicken is offline   Reply With Quote
Old 08-08-2012, 12:45 PM #33
ETH13
 
 
ETH13's Avatar
 
Join Date: Feb 2012
Location: South Jersey
ETH13 has achieved Level 2 in PbNation Pursuit
Thanks so much, finally works.
ETH13 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump