[acidcustum]

Hey Vapor owners
Could someone tell how the trigger is adjusted also post some pictures of the forward/back adjustment, I take it that the magnet in the body attracts the top screw. Looking to use repelling magnets and putting them where the bottom finger would go as this is only for ego upgrade boards I have been told. would this be a good location for the repelling magnets

thanx for any help

john

[acidcustum]

No-one have a camera or just not interested ?

[PaulE2Cocker]

check armory paintball he hhas a few pics posted on his website im in process of working deal to trade my dm12 for his vapor so wont have pics or gun till next week when he back in town.. but on his pics he has good pic of trigger out of gun to see adjustment screws and bends.. when will trigger be available like a mentionad about axe triggers i will buy a prototype to test and give my opinion or if you need a trigger to mark off of when i get his vapor i could send you spare trigger..

[LuLuTheMonk]

I would be very interested in a acid customs trigger as well. Let me know if you need anything else. I can also just send you my extra trigger as well.

[acidcustum]

Thanx LULU
Just what I was after, I already have a trigger.
I can fit in a repelling magnet in the bottom of the trigger slot perfectly
where is the back stop adjustment screw or is there not one, rear travel screw does the trigger just use the microswitch to stop on if so that is bad for the switch
how come there are 2 different trigger designs I see

john

[acidcustum]

Originally Posted by PaulE2Cocker

check armory paintball he hhas a few pics posted on his website im in process of working deal to trade my dm12 for his vapor so wont have pics or gun till next week when he back in town.. but on his pics he has good pic of trigger out of gun to see adjustment screws and bends.. when will trigger be available like a mentionad about axe triggers i will buy a prototype to test and give my opinion or if you need a trigger to mark off of when i get his vapor i could send you spare trigger..

Thanx for the offer of the trigger but I already have one to work from,
Trigger can't say when available as the last time I did I got an infraction but when I have worked out all the last changes to the drawing I will cut one then post pictures,then it will be off for testing.

[LuLuTheMonk]

I will take another picture tonight, but essentially the bottom tang acts as a 'stop' against the microswitch as well. After being used to 4-way adjustable triggers, this was a bit finicky to get something close to how I like my triggers set.

[acidcustum]

I will work making it 4 way adjustable as that design is not good for the microswitch
LULU could you meaasure the distance from the top of the frame to the bottom of the trigger slot

thanx
john

[LuLuTheMonk]

Looks like it is about 2 7/8" (don't have anything metric handy at the moment =/ ) if I understood your question correctly


Also to try and show what the bottom part of the trigger does:

[acidcustum]

Thanx for that LULU not quite what I wanted but I could work out what was needed.
4 way trigger will be cut this weekend, I will post pictures next week

[ProMod]

Hey Acid!

Sorry for the late response, I didn't see this thread until just now. I'll use my calipers and get you some more accurate measurements and pictures in just a moment.

[ProMod]

Yellow Dot Inbound!

[acidcustum]

Originally Posted by ProMod

Yellow Dot Inbound!

Thanx for the help
I should have the first test one cut next week

john

[ProMod]

Originally Posted by acidcustum

Thanx for the help
I should have the first test one cut next week

john

Wonderful!

If you were stateside, I'd offer to mail you my vapor to mock-up the trigger, but I don't know what shipping to Australia would cost

[acidcustum]

Originally Posted by ProMod

Wonderful!

If you were stateside, I'd offer to mail you my vapor to mock-up the trigger, but I don't know what shipping to Australia would cost

its not the shipping from the US its shipping it back is for some reason twice your price and the paperwork is a PITA as they are classed as firearms here have to get import permit and customs pick up can take upto 2months to get them as they have to get tested and other sh*t.
But the trigger is going to be a simple one anyway not complicated for no reason like the ego's have been lately

[LuLuTheMonk]

Thanks for the update. Hypothetically, would that case be true even if just the grip frame was shipped instead of the entire marker?

[acidcustum]

No just a frame no problem
but I shouldn't need one as the changes are to just the area of the finger which isnt used the rest will be the same just a different design at the outside actual trigger end

[acidcustum]

Did first cut today just have to make minor change to the width of the microswitch area drill pushed a slug of C/F out as the side was too thin, just increased width there and will do another tomorrow

[acidcustum]

Pictures of finished Trigger

With the stock trigger



Showing the 4 way adjustment



Magnet to be glued into the trigger slot



ENJOY

[yellowjacket77]

Looks great!!!!

[Automatic Thrill]

Nice. Let us know when you start production.