Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 05-26-2012, 06:11 PM #1
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
Mini reg mod fps to high

I'm runnin about 300 turned all the way down I wanna b at like 280 tops is ther something that can help ?
Fulltiltsplat780 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 05-26-2012, 06:20 PM #2
FallNAngel
Vicious Circles
 
Join Date: Oct 2002
Location: right here
Annual Supporting Member
FallNAngel is a Supporting Member
 has been a member for 10 years
FallNAngel is playing at Living Legends VI
FallNAngel is playing at Living Legends VII
FallNAngel supports DLX Technology
remove any shims in your LPR.
__________________
If you want to set off and go develop some grand new thing, you don't need millions of dollars of capitalization. You need enough pizza and Diet Coke to stick in your refrigerator, a cheap PC to work on, and the dedication to go through with it. We slept on floors. We waded across rivers. -John Carmack
FallNAngel is offline   Reply With Quote
Old 05-26-2012, 07:04 PM #3
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
The lpr is in the barrel right or do u mean the mini reg
Fulltiltsplat780 is offline   Reply With Quote
Old 05-26-2012, 10:27 PM #4
dr.strangelove
The Angel Eye Doctor
 
dr.strangelove's Avatar
 
Join Date: May 2003
Location: Earth
 has been a member for 10 years
Looking at the gun as if you were going to shoot yourself in the face with it, the LPR is located in the bottom left tube behind the hex end cap.

It's worth mentioning: turning the mini-reg adjustment screw in (clockwise) turns the pressure (and consequently velocity) down. Turning it out (counter-clockwise) turns it up. Some regs are reversed from that configuration. So make sure your mini-reg is actually turned all the way down before you set about changing your LPR pressure. Having the LPR gauge is really helpful if you're going to tinkering there.
dr.strangelove is offline   Reply With Quote
Old 05-26-2012, 11:31 PM #5
Ryan10
Father of 3
 
Ryan10's Avatar
 
Join Date: Nov 2010
Location: Philadelphia, PA
Wait, what angel is it??
Ryan10 is offline   Reply With Quote
Old 05-26-2012, 11:47 PM #6
dr.strangelove
The Angel Eye Doctor
 
dr.strangelove's Avatar
 
Join Date: May 2003
Location: Earth
 has been a member for 10 years
I'm assuming its the same gun from his previous thread: LCD.
dr.strangelove is offline   Reply With Quote
Old 05-27-2012, 08:14 AM #7
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
Nope it's my angel force fly 04 when u say shims u mean the actual shims not the springs right ?
Fulltiltsplat780 is offline   Reply With Quote
Old 05-27-2012, 08:54 AM #8
dr.strangelove
The Angel Eye Doctor
 
dr.strangelove's Avatar
 
Join Date: May 2003
Location: Earth
 has been a member for 10 years
In that case your LPR is on the opposite side.

Are you using a HP tank? If your tank's output is above 800 psi, perform the mini-reg spring stack mod by removing one of the spring washers and flipping the next one over. Your mini-reg spring stack before the mod should look like this:

) ( ) ( ) (

After the mod it should look like this:

) ( ) ( (

I wouldn't recommend changing around your LPR without the gauge tool until you've checked that out.

You should have a small gauge on the inside of the flash tank. That is your mini-reg pressure. What is it reading?
dr.strangelove is offline   Reply With Quote
Old 05-27-2012, 08:58 AM #9
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
I did the mod but my gauge says 300 so can I take shims out of the mini reg or something to get it lower ?
Fulltiltsplat780 is offline   Reply With Quote
Old 05-27-2012, 10:59 AM #10
AngelKeeper
 
 
Join Date: Dec 2010
Has anyone told him where to find the manual? It's obvious he has no idea what he's doing, and doing to a force 4 fly at that :|

http://imgs.pbnation.com/manuals/594.pdf

Do yourself and angel owners everywhere a favor, and read the manual or send it to someone capable of doing it...
AngelKeeper is offline   Reply With Quote
Old 05-27-2012, 05:44 PM #11
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
I'm good with these guns the only thing I'm not comfortable with is the reg I've never needed to open it up Im not sending to a guy way out and shell out a ton of $$ for something I can just ask people for advice this is a help forum so if I need help should I go somewhere else I just had a simple question cuz I'm playing today I know wats wrong with my LCD but can't fix it wer I am so I had to swap my force to hpa for the day
Fulltiltsplat780 is offline   Reply With Quote
Old 05-27-2012, 06:40 PM #12
dr.strangelove
The Angel Eye Doctor
 
dr.strangelove's Avatar
 
Join Date: May 2003
Location: Earth
 has been a member for 10 years
If you've never disassembled your mini-reg, now's your chance. You might want to check that the o-ring on the face of the small piston isn't missing. I'm sure it could probably use a proper greasing as well if you're never had it apart before now.

Don't change your LPR just yet though. Focus on trying to get your mini-reg pressure down first.
dr.strangelove is offline   Reply With Quote
Old 05-27-2012, 11:18 PM #13
Fulltiltsplat780
BRAAAP!
 
Join Date: Jan 2012
Location: Collingwood area,Ontario
Ya well I already took it apart for the reg mod everything looked good but I don't Remember a ball in ther but I'll look for it wen I switch it back to lp thanks anyways I just played at 300 didn't get any big complaints I'll switch it back in a few days and get back to work on my LCD

Last edited by Fulltiltsplat780 : 05-28-2012 at 11:47 AM.
Fulltiltsplat780 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump