The Ultimate Empire Prophecy thread - Information, Tech, Mods and FAQ

Brules · 03-18-2012, 02:41 PM

I imagine they can do some things similiar to what Dye is doing, and that is coloring the plastic when it is molded since they are similiar materials.

tegan765 · 03-19-2012, 08:57 AM

I did a lil paint job on my prophecy, I think a white prophecy would be a big winner!

tegan765 · 03-19-2012, 09:31 AM

blohmkin · 03-19-2012, 06:26 PM

My prophecy is out of control!!! So I walk into my room today and my prophecy is in my gear bag spinning away. I pull it out and the switch was in the off position and it was still spinning. After I picked it up it stopped spinning and wouldnt turn back on. I pulled it apart and it will only turn on when I unplug the battery and plug it back in while the switch is on. Once I turn it off I have to do the same thing in order to get back on. It will also randomly turn on while the switch is off, while its spinning and I turn the switch on, it will spin faster. When I turn the switch off it will spin slower and i have to unplug the battery to make it stop. Has anyone ever seen boards go crazy like this??? please help!!

WJS · 04-02-2012, 10:23 AM

I'm using the LTE board and I've noticed my batteries don't last long at all, I can't even get through a box of paint before the power-on LEDs are red! I've tried Energizers/Duracells and I also have Eneloops which I prefer to use. But none of these batteries solves my problem of battery life.

Also, if I use the Eneloops, what setting in the VICI config for battery type should I use? Auto seems to be the only choice but I don't think it detects the battery level correctly causing the hopper to shut down.

StuSidekick · 04-15-2012, 09:48 PM

Does oil or grease need to be applied on the drive shaft of the sprocket on a Z2?

How about the bearings?

tyskidmore3 · 04-15-2012, 10:26 PM

Quote:

Originally Posted by StuSidekick

Does oil or grease need to be applied on the drive shaft of the sprocket on a Z2?

How about the bearings?

No sir.

StuSidekick · 04-16-2012, 09:32 PM

The Empire Z2 RF Transmitter Link Kit is needed on the Z2 to enable RF.

Will the following in the link work?
http://empirepaintball.com/paintball...itter-link-kit

I don't think it comes with the special wire harness.

xxjjoosxx97 · 06-18-2012, 03:25 PM

My lTD is having a problems, if feeds fine untill i put it on a gun, then it sucks, i ran the diagnosis test and there was no problems then, any suggestions?

djsnuff · 06-20-2012, 12:19 AM

Quote:

Originally Posted by UNDRPRVLGD_V2

No it doesnt rotate at all once I turn it on, if I use the rip drive to start it, it will begin to try and pulse backwards. I will try the wire harness as you suggested.

mine does this too used it twice same out come what was the fix to this
heeeeeellllllp

rudz · 06-26-2012, 03:58 PM

My z2 sounds like its grinding when its running, it looks like its assembled right. What can cause this?

**Simon** · 06-26-2012, 04:06 PM

One of the parts inside being out of tolerance. You may need a new back bone. Call up paintball solutions and they should be able to help you out.

OR Baller, CST · 07-03-2012, 10:40 AM

What does it mean when the Z2 is only flashing red when it's turned on?

**Simon** · 07-03-2012, 11:40 AM

Dead batteries.

sh4d0vv · 07-04-2012, 08:22 PM

Is the shell of the LE white Z2 made from the same material as the regular Z2 or is it the older style material of the original prophecy?

UNDRPRVLGD_V2 (Banned) · 07-08-2012, 09:36 PM

Who do I need to contact about the sundering wire on the motor, both of mine broke during practice today.

tyskidmore3 · 07-08-2012, 09:54 PM

contact paintball solutions. I've resoldered one motor before.

UNDRPRVLGD_V2 (Banned) · 07-09-2012, 12:21 PM

Called and new part is on its way

Lt. Tank · 07-09-2012, 01:03 PM

Might be a domb quesstion but just new to prophecy V2. I tested out in practice yesterday and if taken all the way to been Empty and reload it will not get balls down to the firing chamber and since its none there, It will not fire.

Any advice other than hitting the loading bottom 2 times (it worked that way yesterday)

thanks

96montels · 07-10-2012, 06:43 PM

Will a Z2 front fit the original Prophecy (v1, v2)?

Got Cookies · 07-15-2012, 03:35 AM

I just got the camo V2 3 weeks ago and I have haveing probs....yesterday it was jamming like crazy on my last game of the day. Thinking it was the batterys, I changed them with fresh Duracell AA's. Today I went to play and the loader wouldn't feed and the LED was flashing red. I change the AA's again thinking I may have bought a bad pack of batterys and still flashed red. Now it will not even turn on. What should I do? Should I contact PB solutions? or take it back to the local shop? I have only used it 5 times with nothing but reballs so it isnt dirty and I have only used it indoors. so it hasnt gotten wet or anything like that.