[TheHef]

Man now I have to buy this. I was hoping I could just tell myself "its smooth enough as is" , but it looks to good in the video.

[Alter E G O]

GAT's G6's are working verywell

[agdstorminnorman]

You should see it with my new juit bolt. Maybe I can get a video up with it.

[dneyn]

Played in the snow last weekend and I had to raise my LPR or I couldn't shoot more than 230 fps. I probably raised it to about 80 psi.

Today, I had some air and I decided to tune my G6R a bit. I think I got the LPR to about 60, but it would fluctuate from just under 60 to 62 between shots. Not sure what my HPR is though.

I was using a .670 brass insert in a Deadlywind barrel with some reballs. My hand-held chronograph read 310-315. I think this would be perfect for some paintballs with a slight overbore.

[Alter E G O]

My asa on my g6 is leaking like a siv, i replaced and lubed all orings even the oring in the asa but its still leaking bad. air is coming from the open space behind the second screw inside the grip???????

[dneyn]

Originally Posted by Alter E G O

My asa on my g6 is leaking like a siv, i replaced and lubed all orings even the oring in the asa but its still leaking bad. air is coming from the open space behind the second screw inside the grip???????

Tank oring?

[Alter E G O]

Originally Posted by dneyn

Tank oring?

changed it, ill try another

[Alter E G O]

Originally Posted by Alter E G O

changed it, ill try another

still leaks

[gamer565]

Call Blast monday.

[ThePlacidCactus]

Did you install that LPR gauge on your pressure tester? if so where did you get it?

[spydermn11]

i am digging that guage too!

[dneyn]

Test firing the G6R in the backyard in the snow and 60 psi on the LPR isn't high enough. Only got about 260 fps. I raised it to 75 to shoot 300 fps.

[nin7474]

Getting my NEW G6R+LP Poppet soon with Pressure Tester.
Please correct me on steps on how to "TUNE" it.
1.Pressure Tester installed(obviously), turn both screws on the LPR and REG. FLUSH
2.gas up with my NINJA 50/45 with ALL SHIMS out(not getting a SLP Reg)
3.Slowly adjust till i??
4.this is where i'm confused. Am i shooting for Colorado719 Settings, HPR 180-185psi+LPR 60psi?
Sorry for my stupidity

[dneyn]

Originally Posted by nin7474

Getting my NEW G6R+LP Poppet soon with Pressure Tester.
Please correct me on steps on how to "TUNE" it.
1.Pressure Tester installed(obviously), turn both screws on the LPR and REG. FLUSH
2.gas up with my NINJA 50/45 with ALL SHIMS out(not getting a SLP Reg)
3.Slowly adjust till i??
4.this is where i'm confused. Am i shooting for Colorado719 Settings, HPR 180-185psi+LPR 60psi?
Sorry for my stupidity

The LP poppet allows for a lower HPR psi, not particularly for the LPR.

60 psi is really low. I've got about 12 cases through my G6R and 65 psi still isn't high enough. You're gonna have trouble getting 260+ fps per shot. 70-75 is good. Perhaps even 80 just to get good consistency if you're in a cold environment. Once you got that, you can take your tester off and shoot some paint to adjust your HPR until you get around 295 fps. Shoot a few cases through it then adjust your LPR and HPR again.

[nin7474]

Originally Posted by dneyn

The LP poppet allows for a lower HPR psi, not particularly for the LPR.

60 psi is really low. I've got about 12 cases through my G6R and 65 psi still isn't high enough. You're gonna have trouble getting 260+ fps per shot. 70-75 is good. Perhaps even 80 just to get good consistency if you're in a cold environment. Once you got that, you can take your tester off and shoot some paint to adjust your HPR until you get around 295 fps. Shoot a few cases through it then adjust your LPR and HPR again.

Cool
I'll adjust my LPR for 70-75 and the HPR with reballs. How about DWELL SETTING?
Leave it Stock since it's new?

[gamer565]

Originally Posted by nin7474

Cool
I'll adjust my LPR for 70-75 and the HPR with reballs. How about DWELL SETTING?
Leave it Stock since it's new?

States in the first post what you could run the dwell at...

Others through out the thread have also stated what they have there dwell at, or you could so the easy and simple route and just leave it at stock.

[nin7474]

Originally Posted by gamer565

States in the first post what you could run the dwell at...

Others through out the thread have also stated what they have there dwell at, or you could so the easy and simple route and just leave it at stock.

Thanks
Easy and simple sounds good, Stock it is

[nin7474]

Would STOCK DWELL be fine if i got 4C 4yes?

[Alter E G O]

Still having ASA issues......

[nin7474]

Originally Posted by Alter E G O

Still having ASA issues......

This you try his fix in the video?
http://www.youtube.com/watch?v=UXB_xz0H8O0

[adamnewff]

i put mine to what i think is 65 lpr and 185 hpr and it shoots between 290-300 very consistantly with decent feild paint. having around 10 cases thru.

if i got any lower on the lpr my gun wont cycle, but i find it great at 65. really really quite and smooth