[Sick420]

Eric,
Never mind
Thanks

[Whitefox2474]

Originally Posted by SHOOTNPOO

What are your board settings at?
Also what fire mode are you in.

Eric

Firing mode - PSP
Dwell - 10.5 ms
Debounce - 4 ms
Eye Delay - 4.5 ms
Eye Sens. - 13
Bolt Delay - 6 m/s
Clearing Shot - On
FSDO Time -90 sec
FDSO Dwell - 1.5 ms
Loader Pulse - 20 ms

Any suggestions?

[SHOOTNPOO]

Originally Posted by Whitefox2474

Firing mode - PSP
Dwell - 10.5 ms
Debounce - 4 ms
Eye Delay - 4.5 ms
Eye Sens. - 13
Bolt Delay - 6 m/s
Clearing Shot - On
FSDO Time -90 sec
FDSO Dwell - 1.5 ms
Loader Pulse - 20 ms

Any suggestions?

Put bolt delay at 8.0ms
The marker wants to cycle to fast

[monty318]

Just got a creed in a trade, I can not get it to turn on. Is there something certain i need to do? I just charged it for about 90min?

[SHOOTNPOO]

Unplug the batt with the charger unplugged from marker. Leave batt unplugged for 15 min. Plug batt back in ,then charger. That should take care of it as the microprossesor needs to be reset for charging to recycle itself.

Eric.

[monty318]

should it turn on while it is on the charger?

[SHOOTNPOO]

After about 10 min in the charger if the batt is good then it should turn on.

[monty318]

where can i buy a new battery for a creed?

[SHOOTNPOO]

Vanguardus.com
Go the the store and all parts for everything vanguard creed is in their.

Eric

[Meekajahama]

Hey I know it's no longer supported but could you provide me with the oring sizes for the valve body on a v1 creed.

[SHOOTNPOO]

2) 016
1) 611
1) 008
1) 806

Eric

[griffan2]

im thinking of buying one with some money i made on a few sales, but the warrenty is only for the origonal owner. if i get one and it breaks down, what options do i have?

[SHOOTNPOO]

You have to send it into the service center and pay the service fee+ parts.

If you pm me we are selling off some of our Factory team markers that will come with the full warranty still since they were from factory team and never sold.

Eric

[RSASeraph]

hey .. i got a new champagne silver creed with low pressure ram.
Awesome marker ... 2 questions though pls.

When the marker is aired and i press the bolt or the silver bolt pin , it vents air. Is this standard and normal , or do i need an o-ring switch somewhere?

Nr 2:
Ive been looking through the forums but my search-fu is weak. What are the optimal settings for the creed with low pressure ram and should i only apply those settings once run in , or can it be done immediately.

Thanks in advance.

[SHOOTNPOO]

You may need to change the 806 oring onthe internal valve for the ram slide.
This will help the leaking when you push down the bolt. Or just dont push down on the bolt. LOL.

You need to let the marker work in the orings by letting them seat in prior to making changes. I recommend you let the marker get around 6-10 cases prior to making drastic changes.

Eric

[RSASeraph]

thanks shootnpoo. The reason i ask about the bolt thing is that someone picked it up while i was giving a demonstration to a few interested ppl ... i never knew. Was also wondering why he is pushing on the pin .. but hey ... now i know hehe.

[SHOOTNPOO]

No problem anytime.

Eric

[makeshiftballer]

what should my ramp config settings be set at for regular psp ramping? neither ramp or psp mode seems to be ramping correctly

[SHOOTNPOO]

3 pull
3 release
1 reset
3 semi
3 burst

[makeshiftballer]

Thanks!

[p-baller100]

Quick Question, I wanted to know your recommendations for lube and also where you would put oil and grease. So far I've been using vanguard's oil for everything except the hpr where I used dow 33 and I believe I used a little dow 33 on the lpr. But what are your recommendations.