Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 09-22-2010, 09:51 AM #1
weston579
 
 
weston579's Avatar
 
Join Date: May 2003
Location: Statesboro, Ga.
 has been a member for 10 years
eblade 3 way will not seal?

i have an older cocker that i pulled out of my closet to lest a friend play with a few weeks age. The three way on the eblade wont seal, so i took it apart and greased everything. same thing, so i took the entire gun apart to clean and lube. when i got it back together same thing. at one point i was very good with cocker however over time i have lost the skill. so i got a new battery, new three way noid and still the same problem

thanks for any help
__________________
my old feedback
http://pbnation.com/showthread.php?s=&threadid=362542
weston579 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 09-22-2010, 12:27 PM #2
ficone
 
 
ficone's Avatar
 
Join Date: Mar 2006
Location: Brooklyn/Oneonta NY
ficone owns a Planet Eclipse Ego
ficone has achieved Level 1 in PbNation Pursuit
ficone has perfected Level 1 in PbNation Pursuit
Have you tried lubing up the manifold gasket in your noid as well as the orings inside the piston? If not try that and if problems continue you can buy a new noid from paintballgateway or search the bst for a gently used one. Also i have seen many funny things happen if you dont use a fresh batt. Give it a try also.
ficone is offline   Reply With Quote
Old 09-22-2010, 12:34 PM #3
Dk-79
SCHWING!
 
Dk-79's Avatar
 
Join Date: May 2004
Location: North County, California
 has been a member for 10 years
Dk-79 is reppin' sidebar 4 life
Your LPR may have creeped up too. The solenoid's got a bleed valve that opens at around 100psi IIRC.
__________________
Dk-79 is offline   Reply With Quote
Old 09-22-2010, 12:59 PM #4
weston579
 
 
weston579's Avatar
 
Join Date: May 2003
Location: Statesboro, Ga.
 has been a member for 10 years
greased the old noid and lubed everything in it didn't work so i got a new one. same problem. i also rebuilt the rock reg an started turning it in as i aired the gun up. still same problem. it is blowing pretty hard out of the front so i will check the lpr again.. thanks
__________________
my old feedback
http://pbnation.com/showthread.php?s=&threadid=362542
weston579 is offline   Reply With Quote
Old 09-22-2010, 01:49 PM #5
tacxplosion
 
 
tacxplosion's Avatar
 
Join Date: Sep 2007
Location: Guatemala (for real)
have you looked at your ram piston o'ring? if it has a leak the 5-way will also leak.
tacxplosion is offline   Reply With Quote
Old 09-22-2010, 03:46 PM #6
JFGhost
 
 
JFGhost's Avatar
 
Join Date: Oct 2005
How long was it sitting for? I have a Karni with an E2, and it has been sitting for 2 years now...I aired it up the other day and everything was still good.

If your LPR is good, and your SURE it is coming from the noid, not any hoses around it, I would say the gasket between the noid and housing is shot. You also need to be sure you put the gasket on correctly...and you did smear lube on the noid gasket right?

If its none of that...check the ram like was said above.
JFGhost is offline   Reply With Quote
Old 09-22-2010, 08:11 PM #7
weston579
 
 
weston579's Avatar
 
Join Date: May 2003
Location: Statesboro, Ga.
 has been a member for 10 years
i did both of the above. no luck what size are the barbs or qev's? im going to replace them next.
__________________
my old feedback
http://pbnation.com/showthread.php?s=&threadid=362542
weston579 is offline   Reply With Quote
Old 09-22-2010, 08:30 PM #8
JFGhost
 
 
JFGhost's Avatar
 
Join Date: Oct 2005
whoa....replace the hose before the barbs....i highly doubt the barbs are shot. Barbs don't go bad from sitting there.
JFGhost is offline   Reply With Quote
Old 09-23-2010, 02:10 PM #9
Dk-79
SCHWING!
 
Dk-79's Avatar
 
Join Date: May 2004
Location: North County, California
 has been a member for 10 years
Dk-79 is reppin' sidebar 4 life
Unless it's leaking from the barb and not the solenoid.

It could just be a bad solenoid gasket or your solenoid isn't screwed down flat.

If I was holding your gun I'd have it figured out in no time.
__________________
Dk-79 is offline   Reply With Quote
Old 09-24-2010, 01:37 PM #10
weston579
 
 
weston579's Avatar
 
Join Date: May 2003
Location: Statesboro, Ga.
 has been a member for 10 years
thanks guys i think the screw was holding the gasket off. then the barb started leaking. so more than one problem being teched at once
__________________
my old feedback
http://pbnation.com/showthread.php?s=&threadid=362542
weston579 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump