Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 02-03-2010, 11:20 PM #1
deathand
 
 
Join Date: Jan 2010
Getting consistent FPS from an 1998 Stock Autococker

Hello All,
I recently purchased an old 1998 Stock Autococker and I LOVE it! Everything appears to be stock (except for the trigger frame) and in good condition (this is my first cocker, so its possible I'm wrong).
It shoots pretty well, but when I chronoed the marker I noticed that it shoots between 260-289 FPS. Is there any way to get more consistency as far as FPS goes? I don't have a problem replacing parts, but I'd like to get a better idea of what parts should be replaced in order or priority. Any insight you people could give me would be greatly appreciated. Thanks in Advance!
deathand is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 02-04-2010, 10:35 AM #2
deathand
 
 
Join Date: Jan 2010
I posted this on another forum and they asked a few questions so I'll post the responses

I'm using a 5-pc barrel kit and compressed air.
deathand is offline   Reply With Quote
Old 02-04-2010, 12:24 PM #3
peachesarenottasty
 
 
peachesarenottasty's Avatar
 
Join Date: Jun 2009
Location: EsconGhetto, Ca
peachesarenottasty is playing at Living Legends III
peachesarenottasty supports Team VICIOUS
peachesarenottasty supports Pev's Paintball
peachesarenottasty has achieved Level 3 in PbNation Pursuit
5-pc barrel kit?!?!?!!?!


Clean and lube regulaor, otherwise, get a new one is all i can think of. What kind of tank are you using? crossfire, dye, etc.
__________________
peachesarenottasty is offline   Reply With Quote
Old 02-04-2010, 08:17 PM #4
deathand
 
 
Join Date: Jan 2010
Its a no name tank...Pure Energy something or other...I'll try your suggestion next peaches and see if I get anywhere.
deathand is offline   Reply With Quote
Old 02-04-2010, 11:33 PM #5
Magmoormaster
aka Maggy Moo
 
Magmoormaster's Avatar
 
Join Date: Jun 2008
If your reg isn't making it consistant, its probably time to replace the springs.
Magmoormaster is offline   Reply With Quote
Old 02-09-2010, 10:24 PM #6
3sleeper3
Evo IX RS
 
3sleeper3's Avatar
 
Join Date: Oct 2009
Location: Charlotte, NC
Make sure you are using good high quality paint when you chrono...using cheap paint can cause fps inconsistencies which are sometimes mistakenly blamed on the marker.
3sleeper3 is offline   Reply With Quote
Old 02-10-2010, 06:22 PM #7
MurderFX
 
 
MurderFX's Avatar
 
Join Date: Oct 2007
Location: Cincinnati, OH
Also to add about paint - with an autococker always make sure the barrel is level or slightly pointing up while chronoing, especially if you don't have a great paint bore match with the barrel.
__________________
Kevin
~ owner & driver of cars ~

Oklahoma D-Day 2012 - German Army - Join the fun
MurderFX is offline   Reply With Quote
Old 02-23-2010, 07:30 PM #8
p8ntballa100
 
 
p8ntballa100's Avatar
 
Join Date: Aug 2009
Location: I'm around
underbore and see if you have as many problems bc its prolly from roll outs
p8ntballa100 is offline   Reply With Quote
Old 02-25-2010, 01:42 AM #9
ogcocker
 
 
Join Date: Mar 2009
Yep. All good info. I still shoot a 98 I've had since it was new. I get +/- 5 fps. Like they said, paint barrel match and a quality, maintained reg are typically the most important.

Also, if it is stock, you are going to want to pull the valve and lube it, and probably get a spring kit to replace the valve spring and mainspring. This will have a noticeable impact on your velocity consistency. Also make sure your hammer is adequately lubed. These steps will make sure that the valve gets struck with nearly the same force every time, and stays open the same amount of time every shot. The impact on velocity should be obvious, but this is an often overlooked issue.

If this is your first autococker, you may not be familiar with how to remove the valve. Google it, search here, there are guides around. Note, you don't need a valve tool per se, and can use the proper size allen wrench ( forget what size, but you can look it up), but it's good to have around. I made my own by using a dremel cone-shaped grinding tip and boring out the end of the allen key. Look at a picture of an actual valve tool and you'll see what I mean.

Enjoy it man. You'll probably want to upgrade it at some point. The most bang-for-the-buck upgrades will be a shorter throw 3-way, new ram (mp4 is nice and you can find them relatively cheap sometimes), and a roller sear. This will give you a much nicer pull and smoother action.
ogcocker is offline   Reply With Quote
Old 02-25-2010, 04:00 PM #10
dirk.baumann
Farbgruppe Mitte
 
dirk.baumann's Avatar
 
Join Date: May 2007
Location: Germany
dirk.baumann owns a Planet Eclipse Lv1
Try another inline regulator. My 98 went from +/-20 fps (stock inline reg) to +/- 5 (AKA Sidewinder).
dirk.baumann is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump