 |
|
01-09-2009, 07:54 PM
|
#64
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by jakeochoa16
ok the bolt in my mini bolt will stay forward when i air it up and it shoots by itself without me turning it on like its on auto or something what do i do?
|
Make sure that the gun is set near 200psi. I am not sure what the problem is, but the solenoid activates and pushes the bolt forward and then deactivates and the spring on the bolt pushes it back again. So you have a problem with one of those two things. First make sure the solenoid is clicking when you have no air on the gun. Also, make sure there's a spring on the bolt. Once you check those three things comes back and let us know what you found.
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
01-09-2009, 08:27 PM
|
#65
|
|
Σπ Sigma Pi
Join Date: Mar 2008
Location: Marietta, GA
|
Also make sure that your spring is on the correct way.
__________________
R.I.P.Isocracy we were so crazy
|
|
|
|
|
01-12-2009, 03:38 PM
|
#66
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by FBHS RAINMAN
Also make sure that your spring is on the correct way.
|
Yep, make sure it's there and if it is; it's on the right way. I'm fairly sure it's hard to mess up, but we've all seen what people are capable of. Make sure you come back and let us know what the issue was if you fixed it or give us some more details if you didn't.
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
|
01-13-2009, 08:56 PM
|
#67
|
|
Join Date: Jun 2008
Location: MA
|
Mini issue.. selenoid?
even with a new batterie.. i will shoot the gun and i will need to pull the trigger for 30 seconds (light is flashing, indicating shooting) before the marker finally starts clicking.  |
|
|
|
|
01-13-2009, 09:09 PM
|
#68
|
|
Σπ Sigma Pi
Join Date: Mar 2008
Location: Marietta, GA
|
Clean and reset your solenoid piston.
__________________
R.I.P.Isocracy we were so crazy
|
|
|
|
|
01-14-2009, 05:32 AM
|
#69
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by FBHS RAINMAN
Clean and reset your solenoid piston.
|
Si!
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
|
01-19-2009, 01:09 PM
|
#70
|
|
i come from the water
Join Date: Dec 2007
Location: Ballwin,MO
|
when i first got my mini mine wouldnt shoot and the light was flashing red and greeen at the same time... it was weird
it turned out that the board had cracked ( ijust saw tht u didnt have it up there for not shooting)
__________________
92 % of PBnation would be dead if Hostile Kids said breathing wasn't agg. If you're in the 8% that would celebrate the mass suicide of the fanboys, put this in your sig
DunkinDonuts Creating backplayers on a daily basis
PM6 For sale or trade for PUMP
|
|
|
|
|
01-28-2009, 11:14 PM
|
#71
|
|
Join Date: Mar 2008
Location: columbia, mo.`
|
=@%*&!#@
i have bad blow back it will brake 1 or 2 ball in the stack with out the hoper it shoots th 2nd ball up about a foot i went through this check list and replaced the bat and tryed stock and after market bolt.
If you have blowback, do and check the following.
- Make sure no lube or debris is covering your poppet hole.
- Make sure your poppet O-ring is lubed.
- Make sure your check valve isnt broken in half or missing.
- Make sure your spring is broken in.
- Do a factory board reset or lower your dwell.
- Replace your bolt guide O-rings.
- Make sure the big front bolt O-ring isnt missing.
i tore in to the gun and did not find a check valve it would have been hard to miss if it was there right?
on a side note i cant beleve how much paint and crap was on the upper board wow
|
|
|
|
|
01-29-2009, 09:28 AM
|
#72
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by brando78red
i have bad blow back it will brake 1 or 2 ball in the stack with out the hoper it shoots th 2nd ball up about a foot i went through this check list and replaced the bat and tryed stock and after market bolt.
If you have blowback, do and check the following.
- Make sure no lube or debris is covering your poppet hole.
- Make sure your poppet O-ring is lubed.
- Make sure your check valve isnt broken in half or missing.
- Make sure your spring is broken in.
- Do a factory board reset or lower your dwell.
- Replace your bolt guide O-rings.
- Make sure the big front bolt O-ring isnt missing.
i tore in to the gun and did not find a check valve it would have been hard to miss if it was there right?
on a side note i cant beleve how much paint and crap was on the upper board wow
|
The check valve is actually very easy to miss, and if I'm not mistaken a lot of early edition Minis didn't come with one at all. Under the air transfer manifold are 2 or 3 holes and one of them should have a peice of translucent white plastic inside of it. That's the check valve and it helps regulate a consistent pressure.
When you went through that check list above... what did you do?
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
|
01-29-2009, 10:47 PM
|
#73
|
|
Join Date: Mar 2008
Location: columbia, mo.`
|
ythhtduktyera
every thing but the spring its good its had at least 10 plus cases through it including switch bolts change bat. i looked for the check valve closely dont think i would have missed it this is driving me crazy
|
|
|
|
|
01-29-2009, 10:50 PM
|
#74
|
|
Join Date: Mar 2008
Location: columbia, mo.`
|
note
the thing thet gets me is it has always been flawless one i took it out to play and it was a blender 50 to 70 % of the paint going back it to the hopper. also when it dose it it will get paint all the way in the back of the bolt guide
|
|
|
|
|
01-30-2009, 07:36 AM
|
#75
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by brando78red
the thing thet gets me is it has always been flawless one i took it out to play and it was a blender 50 to 70 % of the paint going back it to the hopper. also when it dose it it will get paint all the way in the back of the bolt guide
|
Alright, so you didn't see the check valve? They cost $3 at this website:
http://www.piranha-evil.com/Mini.htm
It's part #22 and the graph already shows where it goes. You might also want to check your detents and makes sure they are still good. The ball may be rolling and allowing another ball in (and chop it). Lastly, my brother had a Spider that got damage in the chamber (a deep scratch) that started chopping balls, so check for that too. Last... make sure your velocity and pressure aren't set too high. Pressure is controlled by the regulator and velocity is adjusted at the back cap.
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
|
02-03-2009, 07:03 AM
|
#76
|
|
Join Date: Mar 2008
Location: columbia, mo.`
|
check valve
i got my check valve just wanted to check it gos in the air port closest to the front of the gun?
|
|
|
|
|
02-03-2009, 02:04 PM
|
#77
|
|
Self-Taught
Join Date: Sep 2007
Location: 954 / 239
|
Quote:
Originally Posted by brando78red
i got my check valve just wanted to check it gos in the air port closest to the front of the gun?
|
No, it goes in the small hole in the middle of the other two small ones.
Check (how to properly assemble your mini) the picture of the check valve is about a third of the way down on the page. |
|
|
|
|
02-03-2009, 10:46 PM
|
#78
|
|
Join Date: Mar 2008
Location: columbia, mo.`
|
done
well that dose it ha ha ha im not giving up that fixed it who knew something so small and fragile could do so much
not sure i like that design decision
|
|
|
|
|
02-08-2009, 06:13 PM
|
#79
|
|
runner
Join Date: Feb 2008
Location: Pittsburgh
|
awesome thread.
thanks so much
__________________
Hotch
Stormtrooper Invert Mini
modded VSC Phantom
MKX Alias rocket launcher
|
|
|
|
|
02-09-2009, 03:43 PM
|
#80
|
|
gotgamegotgamegotgame
Join Date: Apr 2008
Location: ate-five-sex
|
Quote:
Originally Posted by brando78red
well that dose it ha ha ha im not giving up that fixed it who knew something so small and fragile could do so much
not sure i like that design decision
|
Awesome! Good to hear 
__________________
+100 || Annual Supporting Member Council || -0
Flawless Victory
☆ ☆
|
|
|
|
|
02-16-2009, 12:26 AM
|
#81
|
|
B.Y.O.B
Join Date: Aug 2008
Location: NOR CAL
|
So if you strip a screw on the solenoid you have to buy a new solenoid?
Is there some other way?
__________________
lol ^
|
|
|
|
|
02-16-2009, 07:06 PM
|
#82
|
|
Down the hatch!
Join Date: Feb 2008
Location: DFW
|
you have to get a new one
__________________
][nvert Mini Dust Silver #7174 ‘‘Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel.
Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are inevitably ruined’’
‘‘The great object is that every man be armed. Everyone who is able may have a gun.’’
— Patrick Henry
|
|
|
|
|
02-19-2009, 08:06 PM
|
#83
|
|
Join Date: Mar 2008
Location: STRONG ISLAND
|
my mini is stuck in milli mode and wont go down or reset, got anything?
|
|
|
|
|
02-19-2009, 08:59 PM
|
#84
|
|
The Fixer
Join Date: Oct 2008
Location: South of Houston
|
maybe try disconnecting the battery
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
