[pananda]

thanks!

[pananda]

oh yeah, and the inflicted, what is the significance of the hole in the maverick frame?

how does this bottomline work?

http://www.doropaintball.com/AB10381...xd.asp?id=8211

[EVA-killer]

is there any barrels out right now that fit the maverick?

[>'_PumP_'<]

instead of going ghetto you could make a pretty solid copper copper 10rd tube.



this pretty basic stuff from your plumbing department in your local hardware store. except for the phantom feed end cap and plastic covering on the cross drilled section. It took a couple days of welding and measuring but its definetly stronger than pvc piping. this right here is my 10 or 15 ball model. i have another one that can hold about 25 balls. this design was based off of a friends ghetto mod and a phantoms feed tube.

[zz rai]

Originally Posted by pananda

oh yeah, and the inflicted, what is the significance of the hole in the maverick frame?

how does this bottomline work?

http://www.doropaintball.com/AB10381...xd.asp?id=8211

No, that will not work. What you need is something call the Euro Grip bottomline or Lonestar bottomline.

The only place I know is here, but they have been out of stock, so you might want to call them.

This is what a Euro Grip bottomline should look like, this is from my old set up a while back.

Originally Posted by EVA-killer

is there any barrels out right now that fit the maverick?

14" J&J Ceramic

[grantis2911]

What feedneck do you have on that Maverick? Is it just a fancy clamping elbow or did you mod something?

[mayor]

you can also swap out the grip frame and put a phantom 45 grip frame on it. Thats what I did to my old trracer

[zz rai]

Originally Posted by grantis2911

What feedneck do you have on that Maverick? Is it just a fancy clamping elbow or did you mod something?

No, it's a regular ACI Elbow.

[grantis2911]

Originally Posted by zz rai

No, it's a regular ACI Elbow.

Oh!? That is definetly not the same as the elbow I got in mine. All well.

Originally Posted by mayor

you can also swap out the grip frame and put a phantom 45 grip frame on it. Thats what I did to my old trracer

It there any modding to it or is it just a straight drop in? I would like to do that.

[zz rai]

Originally Posted by grantis2911

Oh!? That is definetly not the same as the elbow I got in mine. All well.


It there any modding to it or is it just a straight drop in? I would like to do that.

Nope, you can't just buy it, and exchange the grips.

[The Inflicted]

Originally Posted by grantis2911

It there any modding to it or is it just a straight drop in? I would like to do that.

No modification needed. It's a straight drop-in. The most you might need to do is use a couple washers on the bolt that holds the grip to the frame- sometimes the stock bolt is just a little too long.

[grantis2911]

Thanks for the replies. Do you know if Phantom breeches will fit a Maverick. Like a center feed one from Wevo?

[zz rai]

I highly doubt it. If it did, we would not have to go to the trouble of modding the feed blocking fit on the maverick's body.

[grantis2911]

Ok has anyone ever centerfed a Maverick then?

[zz rai]

Yes, there are some pictures floating around.

[grantis2911]

Would you know where? or the user that did it?

[mxmtl]

Might as well buy a Phantom if you want a clean centerfeed instead of spending the time and effort modifying the Maverick body.

I need to do more testing on this, but noticed that one of my Trracers without the CO2 filter seemed a little more consistent over the chrono than the two with filters. It was also the loudest. It could also be the valve spring. It came with a blue spring that was stiffer than the stock springs.

[zz rai]

I agree with all money and receivers I spent and wasted on... Just get a Phantom. =]

[mxmtl]

After doing more research, I think you may be able to get more consistency and efficiency with a harder valve spring. I ordered a Maddmann spring kit to do some tuning.

[zz rai]

Spring kit 4 the win ^_^

[noah harper]

just got a maverick, can't wait to "play" wit it.....