[paintballman_13]

They dont. You have to attach a new pod or hold the marker upside down so the balls fall in.

[Crusade]

In the other large Q Loader thread, a few asked which harnesses people have found to work best with the slightly larger Q Loader pods. Has anyone found a harness that does not really require any "modifications"?

My local shop does not have a wide selection to choose from. So any feedback would be appreciated.

I'm sorry if this isn't technical enough of a question, but I thought it'd be best if I did not start a "mini" thread so to speak.

[Andre the Bald Giant]

M-Pack is what they reccomend

[dzastrow]

i know this is kinda askin a lot but if someone could take a tape measure and measue the circumfrence of the pods and measure the length of the pods, id be extremely grateful

[paintballman_13]

Circumfrence about 8 inches and length is about 11.5

[dzastrow]

u da man

[dzastrow]

ok so the feed neck elbow thing stock is rounded, but the warp feed has a 90 degree turn
imagine that this is the warp feed elbow thing
here

-----------------
.......force>>>>>| <wouldnt balls be pushed up agiasnt the wall
----------- ..... | here
...............| .... |
...............| .... |
...............| .... |
...........gun here.......

and that would stop the balls from going into the chamber as fast? with the rounded elbow thing it will keep the force mostly agiasnt each ball pushing them into the breach instead of pushing them just above the breach. i hope im wrong cuz it looks a lott better with the warp feed


dammit the illistration didnt work the first time pretend that the periods arent there

[F=ma]

Originally posted by dzastrow
wouldnt balls be pushed up agiasnt the wall

Its the same reasoning why halo's double feed against detents. Most of the pressure should be DOWN but the Halo's can push the balls hard enough to double feed, so even when the breech has a 90 degree turn, it can still push in a direction at a right angle.

And I believe that a Q-loader has a stronger feed than a Halo, but I could be wrong on that (it would make sense seeing as Q-loader can burst up to 50 bps and halo's do mid 20's)

[fastingrage]

ya but i also have a little piece in there that like the warp adapter and spyder powerfeed plugs angles the entry to increase rof, except mine is radiused and much much smoother. ill get a pic if u want when its back from my machinist in a few days

[Jordan_P]

so how long does it take to fill one pod .

[paintballman_13]

30 seconds max even less when you get good.

[95socalstang]

when loading the qpods with paint can you use another loader? I gotta try to find a use for my Halo once I get the qloader.

Eric

[mulletstation]

lol a halo feeding into a qloader that you then use to fill a quantum with..... delicious.....

[F=ma]

For those of you with Bushmasters, the Black sticker is perfect for cutting out and putting onto the jewel on the gun.

Only thing is it needs to be laminated in order to make sure it will stand up against paint.

Because after all it is just a sticker.

Just trace around the jewel with an exacto knife and walla, your new Q-loader Jewel!

[fastingrage]

eric, it would work, but youd have to ****** rig it and tape it together because they wont fit together, two things (hose and feedneck of loader) that are made to fit into the same size thing wont fit on each other...................... i dont think.....

either way, im gonna tape my old eggo to the tube and use it instead, their podfiller sucks



also does anyone have problems with ball rattle? that was one of the reasons i bought it, but they still rattle a little, is it like this for u, its less than a normal hopper but enough to piss me off because i spent 150 bucks

[bscriver]

They fit in the NXe pod pacs perfect guys

[Avery]

Wonderful bscriver! I was waiting for someone to confirm or deny that! NXe it is! Now... to find a 2+1 pack...

[kyro74]

For those interested in a longer Qloader Video, check out www.paintbrawler.com

On the home page, about 1/3 of the way down, click on where it says "click here for exclusive Qloader video review". The vid is 26 megs and rund about 6 minutes.

Hope this helps answer questions for those who don't have one yet.

[bscriver]

Anyone find if they go from really small paint to really large paint they have to change hose size? As well I cut the hose as per directions in the manual, but since an even number of balls will not fit between the end of the q loader elbow and the top of the bolt, the instruction are moot for my setup, you might want to check hose length, combined with feed neck space, for a truly accurate fit.

As well ive recently encountered a problem with ball choping in the top of the q pod, maybe my tensions up, but it could an old paint issues. let me know if you guys have had any of these probs, and how you went about remedying them

Also anyone know the acctual use of the tube materials use, I'd like to get a quanity of it, but i need to knpow what its used for
Thanks

[F=ma]

Originally posted by bscriver
As well ive recently encountered a problem with ball choping in the top of the q pod, maybe my tensions up, but it could an old paint issues. let me know if you guys have had any of these probs, and how you went about remedying them

My Q pod would jam up every now and then, when I pulled it out of the loading socket, I found that the ball at the exit hole was being pinched.

Bear in mind it never did that all morning, but it happened more in the afternoon.

Is paint super sensitive to being left out in the sun? It was a sweltering day, and the paint may have gotten a little soft in the heat.

Also I dropped some of a bag onto the ground (grass/dirt) and that may have contributed to the shell getting a little soft.

Although I will say I had zero problems that morning when all the paint I loaded into it was fresh.

The paint was Heat, and I was running with 14 prewinds.

[Avery]

I have personally confirmed the following packs:

DO WORK
=======
NXe
Extreme Rage
X-Cel


DO NOT WORK
==========
Redz Dimension
Dye Proto
Xtreme Enterprises Pro
Mantis