Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 04-15-2008, 03:18 PM #1
gunhorr239
i smell rice
 
gunhorr239's Avatar
 
Join Date: Nov 2006
Location: so fla .
marq 7 stock board questions..

how do i change firing modes? and rof?
__________________
trust
gunhorr239 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 04-15-2008, 03:53 PM #2
Shocker_Monkey
KCCO
 
Shocker_Monkey's Avatar
 
Join Date: Mar 2003
Location: 920 Represent
Annual Supporting Member
Shocker_Monkey is a Supporting Member
 has been a member for 10 years
Shocker_Monkey is playing at Living Legends VII
Shocker_Monkey plays in the APPA D5 division
Shocker_Monkey is Legendary
Shocker_Monkey is Boss
Assuming its the stock board: Dip switches. Check the manual in the stickies.
__________________

==========================================
WISCONSIN NAVARONE
==========================================
2k5'd Timmy FSO - Bring me Xmas funds
==========================================
Shocker_Monkey is offline   Reply With Quote
Old 04-15-2008, 10:43 PM #3
gunhorr239
i smell rice
 
gunhorr239's Avatar
 
Join Date: Nov 2006
Location: so fla .
already tried.. i dont have a pdf viewer on this computer.. and i cant download one either..
__________________
trust
gunhorr239 is offline   Reply With Quote
Old 04-16-2008, 01:25 AM #4
Shocker_Monkey
KCCO
 
Shocker_Monkey's Avatar
 
Join Date: Mar 2003
Location: 920 Represent
Annual Supporting Member
Shocker_Monkey is a Supporting Member
 has been a member for 10 years
Shocker_Monkey is playing at Living Legends VII
Shocker_Monkey plays in the APPA D5 division
Shocker_Monkey is Legendary
Shocker_Monkey is Boss
Dipswitches:
1 off: cycle delay off
1 on: cycle delay on (2 milliseconds)

2 off: min debounce
2 on: max debounce

3 off: normal uncapped
3 on: capped at 15 (or if board flashed 13.33)

4 off 5 off: semi auto
4 off 5 on: 3 shot burst after 3 trigger activations
4 on 5 off: ramp after 3 activations
4 on 5 on: full auto after 3 activations

6 off: dwell 8
6 on: dwell 10

This is off the quick start guide that came with my marq.
__________________

==========================================
WISCONSIN NAVARONE
==========================================
2k5'd Timmy FSO - Bring me Xmas funds
==========================================
Shocker_Monkey is offline   Reply With Quote
Old 04-16-2008, 07:52 AM #5
cerealkiller_
eat a bleepin dorito
 
cerealkiller_'s Avatar
 
Join Date: Jun 2007
Location: *386 FL
cerealkiller_ has achieved Level 2 in PbNation Pursuit
Well does the board have a line on the chip? If so then it is the new software and you should check BL's site for the manual. If not then what monkey posted above will work.

The old settings are completely different from the new frenzy 3.0 software.
__________________
Shoot 50 Designs:I do all kinds of graphic artwork!:
cerealkiller_ is offline   Reply With Quote
Old 04-16-2008, 12:30 PM #6
1max2nv
 
 
1max2nv's Avatar
 
Join Date: Mar 2005
Location: Herndon, VA
1max2nv plays in the APPA D5 division
How do we know if the board was flashed for the 13.33? A line on the chip indicates it?
__________________
PRO Jerseys for sale
1max2nv is offline   Reply With Quote
Old 04-16-2008, 12:47 PM #7
cerealkiller_
eat a bleepin dorito
 
cerealkiller_'s Avatar
 
Join Date: Jun 2007
Location: *386 FL
cerealkiller_ has achieved Level 2 in PbNation Pursuit
Yeah,
If they re-flashed it they mark the chip with a straight line (useually with a silver sharpie)
__________________
Shoot 50 Designs:I do all kinds of graphic artwork!:
cerealkiller_ is offline   Reply With Quote
Old 04-17-2008, 11:44 PM #8
gunhorr239
i smell rice
 
gunhorr239's Avatar
 
Join Date: Nov 2006
Location: so fla .
very useful stuff... thnx guys.
__________________
trust
gunhorr239 is offline   Reply With Quote
Old 04-18-2008, 12:15 AM #9
1max2nv
 
 
1max2nv's Avatar
 
Join Date: Mar 2005
Location: Herndon, VA
1max2nv plays in the APPA D5 division
okay..i have a unflashed stock board. I'm a bit confused. Can the Frenzy 3.0 be flashed on the stock board? or is it a totally different board that you have to buy. I would think Frenzy 3.0 is ideal since you can program the ROF yourself.
__________________
PRO Jerseys for sale
1max2nv is offline   Reply With Quote
Old 04-18-2008, 12:32 AM #10
IgnoranceInABag
 
 
IgnoranceInABag's Avatar
 
Join Date: Sep 2007
Annual Supporting Member
IgnoranceInABag plays in the PSP
IgnoranceInABag plays in the APPA D1 division
^^i think they just flash it to 3.0. i got my gun back from blast and they said they flashed it for 3.0 (they didnt ccually flash it ). sent it back with a manual and everything too

EDIT-they might have flashed it, and im sorry to steal this thread, but is dwell programmable on the stock board? because i was just messing around and i can program my dwell using the 3.0 instructions but i cannot program my ROF cap nor can i program my debounce.
__________________

Last edited by IgnoranceInABag : 04-18-2008 at 12:41 AM.
IgnoranceInABag is offline   Reply With Quote
Old 04-18-2008, 01:06 AM #11
gunhorr239
i smell rice
 
gunhorr239's Avatar
 
Join Date: Nov 2006
Location: so fla .
no clue. and its ok .. as long as we both get basic info on these damn boards
__________________
trust
gunhorr239 is offline   Reply With Quote
Old 04-18-2008, 01:08 AM #12
IgnoranceInABag
 
 
IgnoranceInABag's Avatar
 
Join Date: Sep 2007
Annual Supporting Member
IgnoranceInABag plays in the PSP
IgnoranceInABag plays in the APPA D1 division
you have the stock board right? try flipping the 6th dipswitch on and powering up the board, if it is programable it will flash pink of the number of ms it is set at and then shut down
__________________
IgnoranceInABag is offline   Reply With Quote
Old 04-18-2008, 01:02 PM #13
Unholy
Short for Unholy Bastard
 
Unholy's Avatar
 
Join Date: Aug 2004
Location: St. Louis Area
Unholy is a Supporting Member
 has been a member for 10 years
Bob Long Frenzy 3.0 Board Instructions

To power on marker:
Press power button once and release.

To turn eyes off:
Pull and hold trigger while powering on marker. LED will flash white then release.
To power off marker:
Press power button and hold. LED will flash orange then red and board will power itself off.

LED Indications:
Both 2C eye and 4C eye equipped markers:
Green (Flashing) = Eyes on. No paintball staged in chamber.
White (Flashing) = Eyes off.
Red (Flashing) = Low Battery. Change battery immediately to avoid failure.
Orange (Flashing) = Eye Malfunction. Most likely, paint from ball breaks has blocked eye vision.
2C eye equipped markers:
Violet (Flashing) = Bottom eye tripped. Paintball properly staged in chamber.
4C eye equipped markers:
Aqua (Flashing) = Top eye tripped. Also use this to test top eye.
Blue (Flashing) = Bottom eye tripped. Paintball properly staged in chamber.

Dip Switch Settings 1 through 6:

1 Fine Tune Cycle Delay

(Off ) = No fine tune cycle delay.
(On) = 2 millisecond fine tune cycle delay.

2 Programmable Debounce
Note: Stock debounce setting is 6. Debounce is programmable from 1 to 50.
To check debounce setting:
1. Power off board.
2. Set dip switch on (On) position.
3. Power on board.
4. LED will flash the current debounce setting then power itself off.
To set debounce:
1. Power off board.
2. Set dip switch to (On) position.
3. Pull and hold trigger.
4. Power on board.
5. LED will turn white.
6. Release trigger. ( Over )
7. LED will turn off and then flash the current debounce setting
8. LED will then turn green awaiting your response.
9. Pull trigger to set desired debounce. Example: debounce of 6 = 6 trigger pulls.
10. Wait 3 seconds after last trigger pull.
11. LED will flash back the debounce setting you programmed and board will then power itself off.
12. Check debounce setting to see if correct.
13. Set dip switch back to (Off ) position then reboot your board.

3 Programmable ROF (Rate of Fire)
Note: Stock ROF setting is unlimited BPS. ROF is programmable from 11 to unlimited BPS.
To check ROF setting:
1. Power off board.
2. Set dip switch to (On) position.
3. Power on board.
4. LED will flash the current ROF setting then power itself off.
To set ROF:
1. Power off board.
2. Set dip switch on (On) position.
3. Pull and hold trigger.
4. Power on board.
5. LED will turn white.
6. Release trigger.
7. LED will turn off and then flash the current BPS setting.
8. LED will then turn green awaiting your response.
9. Pull trigger to set desired BPS.
> 1 pull = 11 BPS
> 2 pulls = 12 BPS
> 3 pulls = 13 BPS
> 4 pulls = 14 BPS
> 5 pulls = 15 BPS
> 6 pulls = 16 BPS
> 7 pulls = 17 BPS
> 8 pulls = 18 BPS
> 9 pulls = 19 BPS
> 10 pulls = unlimited BPS
10. Wait 3 seconds after last trigger pull.
11. LED will flash back the ROF setting you programmed and board will then power itself off.
12. Check ROF setting to see if correct.
13. Set dip switch back to (Off ) position then reboot your board.

4 and 5 Firing Modes
(Off ) (Off ) = Normal semi automatic firing mode.
(Off ) (On) = 3 shot burst (activated when 4 BPS is achieved).
(On) (Off ) = Ramping mode (activated when 4 BPS is achieved).
(On) (On) = Fully automatic (activated when 4 BPS is achieved).
6 Programmable Dwell ( Over )
Note: Stock dwell setting is 8ms. Dwell is programmable from 4ms to 25ms.
To check dwell setting:
1. Power off board.
2. Set dip switch to (On) position.
3. Power on board.
4. LED will flash the current dwell setting then power itself off.
To set dwell:
1. Power off board.
2. Set dip switch on (On) position.
3. Pull and hold trigger.
4. Power on board.
5. LED will turn white.
6. Release trigger.
7. LED will turn off and then flash the current dwell setting.
8. LED will then turn green awaiting your response.
9. Pull trigger to set desired dwell. Example: 6 milliseconds = 6 trigger pulls
10. Wait 3 seconds after last trigger pull.
11. LED will flash back the dwell setting you programmed and board will then power itself off.
12. Check dwell setting to see if correct.
13. Set dip switch back to (Off ) position then reboot your board.
__________________
This space for rent

Last edited by Unholy : 04-18-2008 at 01:05 PM.
Unholy is offline   Reply With Quote
Old 04-18-2008, 02:02 PM #14
IgnoranceInABag
 
 
IgnoranceInABag's Avatar
 
Join Date: Sep 2007
Annual Supporting Member
IgnoranceInABag plays in the PSP
IgnoranceInABag plays in the APPA D1 division
thanks but i got the manual. and my problem now is that i can only program my dwell
__________________
IgnoranceInABag is offline   Reply With Quote
Old 04-18-2008, 02:19 PM #15
Impy_but_not_limpy
Mow'n face since 06
 
Impy_but_not_limpy's Avatar
 
Join Date: Jan 2006
Location: 845
Impy_but_not_limpy is a Supporting Member
any one know what the turn around time is to get a board flashed
Impy_but_not_limpy is offline   Reply With Quote
Old 04-18-2008, 03:48 PM #16
IgnoranceInABag
 
 
IgnoranceInABag's Avatar
 
Join Date: Sep 2007
Annual Supporting Member
IgnoranceInABag plays in the PSP
IgnoranceInABag plays in the APPA D1 division
i sent my gun in and got it back in less than a week
__________________
IgnoranceInABag is offline   Reply With Quote
Old 10-18-2008, 08:55 PM #17
brndon076 (Banned)
 
Join Date: Oct 2008
whhere is the dip switch on the frenzy board?
brndon076 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump