R6 Still Leaks Down Barrel - PbNation
Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

 
Archived Thread - Cannot Edit  
Old 06-23-2007, 09:54 AM #1
jow002
 
 
Join Date: May 2007
Location: Southern Cali
R6 Still Leaks Down Barrel

So i read through the Piranaha Repair FAQ, in particular the section about leaking down the barrel, but my R6 still leaks. I don't know whats wrong. there was nothing wrong with the valve o-rings, but i replaced them anways (with tank o-rings *same size and diameter as original valve o-rings, I think?*). i replaced the cup seal with the extra one it comes with, and the valve is in the correct way. Any other help would be really appreciated. i want to see if i can fix the problem before i send it in to PMI. thanks
jow002 is offline  
Old Sponsored Links Remove Advertisement
Advertisement
Old 06-23-2007, 11:55 AM #2
SlavaROKZ (Banned)
 
Join Date: Jun 2007
Location: Las Vegas
did you oil all the o rings. sometimes that all that it takes. Also does it leak down the barrel after you take a couple of shots.
SlavaROKZ is offline  
Old 06-23-2007, 12:31 PM #3
Dead_Body
 
 
Dead_Body's Avatar
 
Join Date: Oct 2006
Location: Burnaby BC, Canada
The brass retaining pin. Did you tighten it? If you tighten it you push the valve body up hard and that lets it leak past the Orings and up into the barrel. The brass pin needs to be in but loose. Let it out until you don't feel any load against the valve body but so that it's still below the surface of the body. The trigger frame will hold it in place so it doesn't come out.

If none of this fixes it then your valve body may be faulty or it was damaged in making it. The valve body has a slightly raised rim around the larger side hole for the cupseal to seal against. Have a look at that and feel it for any sort of ding. Even a small ding or nick is all it would take to loose the seal you're after.
__________________
I just thought I'd take a quick peek and then the world went all yellow.....
Dead_Body is offline  
Old 06-23-2007, 12:51 PM #4
Axle543
 
 
Axle543's Avatar
 
Join Date: Jun 2007
The same thing happened to me.Try replacing the blue hammer o-ring.
Axle543 is offline  
Old 06-23-2007, 01:00 PM #5
jow002
 
 
Join Date: May 2007
Location: Southern Cali
thanks to all. ill take a look at all these today, and post my results. thanks again.
jow002 is offline  
Old 06-28-2007, 08:41 AM #6
clackclackclack
ballin
 
Join Date: May 2007
Location: gahanna, ohia
squirt a ton of oil around the valve
dont even take it out of your marker
you might think that is too much oil, but in blowbacks that is fine
excess iol doesnt mess anything up
just clean your gun out afterwards
clackclackclack is offline  
Old 07-07-2007, 05:53 PM #7
riseabovethelies
 
 
riseabovethelies's Avatar
 
Join Date: Mar 2007
you might have the valve body in backwards thats why mine leaked if not listen to dead body
__________________
If your a gay Paintball player put this in ur sig
If you don't buy into Smartparts corporate bulls**t put this in your sig.
"Originally Posted by android17ak47
You know your addicted to paintball when, someone passes out on the feild, you run up to him and somebody yells to you "check to see if he has a pulse", and you reply, " No he doesnt, he has a vlocity".
VIVA LA AKA
SP destroyed all innovation in paintball.
"the evidence strongly suggests that neither Billy nor Adam (Smart Parts) could have invented the electronic paintgun" -Garr M. King, U.S. Judge
riseabovethelies is offline  
Old 07-28-2007, 10:41 PM #8
usa_patriot (Banned)
 
Join Date: Jul 2007
Location: some where
cock it back or check o-ring for the bolt or the striker
usa_patriot is offline  
 




Posting Rules
Forum Jump