THIS IS NOT MINE Courtesy of Yougotowned
THIS IS NOT MINE Courtesy of yougotowned
Owner tested. Arston approved.
This thread consists of, at this point in time, of:
-Board Stuff(changing modes, activation, LED displays, etc)
Each will have it own post(s) right under each other.
1. What is the recommended operating pressure?
We recommend you set the operating pressure on your DP Fusion at no more than 300 psi, although the ideal pressure is 250 psi. Please refer to the operating instructions for details.
2. How many modes are there?
On the first version of DP Fusion there are four modes: two PSP modes (one PSP legal and one capped at 20 bps) and two semi modes (one capped at 15bps and the other at 20bps). On the newer V2 boards, which are identifiable by 4 dip switches instead of 2, there are a total of 8 modes and the maximum rate of fire is capped at 25 bps.
3. How can I obtain a new board?
New boards can be ordered by emailing customer service at email@example.com
. At the time of this publishing, the cost of a board upgrade is $25.00 with a core exchange. You can refer to the <video> to view step by step instructions in changing the board
4. When my marker is engaged in ramping mode, the balls are dropping instead of firing. What is the problem?
Two major possibilities: a) The OPR / regulator may need to be lubed (see last page of the user’s manual for instructions), or b) The battery may be low - replace battery and test fire.
5. How do I know if the eyes are working?
When the eyes detect a ball in the chamber, the indicator light will turn to solid blue.
6 When do I need to change batteries?
The indicator light will flash red when it is time to change batteries, or the velocity may drop drastically.
7. Why is it that no balls were used but the indicator light is solid blue?
Open the left side of the grip frame and make sure that the plug with four wires on it is completely connected. If this does not solve the problem, contact Technical Support (firstname.lastname@example.org).
8. I notice that I am not able to sustain velocity above 275fps, what is wrong?
There is a leak in pressure, most likely in the OPR. Inspect part #34 and #27 for damage. Rebuild regulator if necessary. Contact Technical Support at email@example.com
9. Help, I hear a hissing noise!
The solenoid may be damaged. Although we do not encourage customers to service their own solenoids as it voids warranty, those that are experienced can contact Dangerous Power for a replacement solenoid piston. There are three O-rings located on the piston, and one or more may be damaged. You can also refer to the (link) to view a step by step guide in replacing the solenoid piston.
10. I’ve been hearing about leaks associated with the regulator. How do I prevent this from happening?
Leaks can generally be prevented by using clean air tanks and avoidance of ‘over pressurizing’ the Fusion. Routinely lubing the OPR with a quality lubricant can also reduce the premature wear of the O-rings, thus preventing air leakage. Please refer to the video section detailing the process of ridding your marker internals of debris, and OPR maintenance.
11. Why is it important to maintain my air regulator?
Maintenance of your regulator will prevent damage to your solenoid, and insure high efficiency and performance. Remember, most leaks can be traced to dirty air tanks or debris within the internals of the regulator.
12. The pressure on my gauge slowly rises after each round of fire. The gauge reading creeps past the recommended 300 psi. Is there something wrong?
You are experiencing a ‘regulator creep.’ Do not continue using your Fusion until you have serviced the regulator, or you may damage the solenoid. Usually, part #34 and #27 can be replaced to fix the problem. Contact Technical Support at firstname.lastname@example.org
13. I am chopping paint, especially at high rates of fire. What is causing this?
First, be sure that the paint you are using is of high quality, and stored properly. Paint and bore size match is crucial to accuracy and avoiding breakage. Generally, if you cannot ‘blow paint through the barrel,’ the paintball is too large for the barrel. Similarly, if paint ‘rolls out the barrel’ easily, the paintballs are too small for the barrel size.
Second, check both ball detents to be sure they are in place, and not ‘stuck’ within the body. They should freely move back and forth with the pressure of your finger. Remove and clean if necessary. Contact Technical Support if you continue to experience problems.
14. My Fusion is experiencing slow rate of fire, what can I do?
This is usually caused by low power from your hopper. Replace the battery. If problem persists, contact Technical Support.
15. What can I do to increase efficiency?
Poor efficiency is usually caused by excessive inline pressure. The ideal pressure is 250 psi, and no more. Clean and perform maintenance of OPR. Paint and bore size match may also be a factor. If you continue to experience poor efficiency, contact Technical Support.
16. What is the RAPS™ ASA, and what advantages does it offer?
The RAPS™ ASA offers easy on/off and no second guessing whether your air tank is engaged or not.
17. What does RAPS™ stand for?
Rapid Air Pressurizing System.
18. My local pro shop carries the Fusion, but does not have the RAPS™. Where can I order one?The RAPS™ can be requested from any dealer that carries the Fusion™ paintball marker.
19. My local pro shop carries the Fusion, but does not have the RAPS™. Where can I order one?
The RAPS™ can be requested from any dealer that carries the Fusion™ paintball marker.
20. How long are Dangerous Power products warranted for? All Dangerous Power products carry a minimum of one (1) year from the date of purchase.
21. What is covered under warranty? Generally, Dangerous Power covers its products from any defects from manufacturing and malfunctions occurring from normal use. Warranties are voided when signs of tampering of product are evident, or products are damaged by unauthorized repair. However, the Dangerous Power Customer Service department will evaluate each case individually.
22. What lube should I use?
The head engineer at DP says to use DOW 55, or products similar to it. Use DOW 55 for the ram, lpr, etc. DO NOT lube your bolt. The bolt is delrin and naturally self lubing, and lube will just make delrin expand. DOW 55 is recommended for swelling the o-rings allowing for a much better seal. DOW 33 and it's similar products such as Hater Sauce, Evil Pus, Dye Slick, Shocker Lube, Sleek, and so on, will work as well with no problems, but DOW 55 is the best.
23. Should I use a High Pressure(HP) or Low Pressure(LP)
Both are fine.HP is reccomended, or an LP with a fast recharge. Be sure you have a good regulator on your LP tank though. Crossfire, Macdev, Empire, CP, Lucky, Draxxus, Geurilla are all good LP air regs.
24. Where is the serial number located at?
On the bottom side of the trigger guard.
25. Where are the detents and eyes located?
On both sides of the gun, there are two thin, diagonal placed plates held to the gun by screws. The detents are there, along with the eyes.
26. What kind of barrel threads do the Fusion use?
The Fusion uses autococker barrel threads.