MARQ Manual!!!

the incubus · 01-30-2007, 12:57 PM

And the very last page makes reference to using 33 in the event you don't have 55. it's in the final Hot Tips.

wowmas · 01-31-2007, 04:23 AM

got it so what is the best seeting for marq on DEBOUNCE should i put Max Setting or Min setting. and also DWELL 8 or DwELL 10

What is DEBOUNCE for and what is DWELL for sorry i know this sounds N008

the incubus · 01-31-2007, 09:21 AM

Debounce is used to reduce/control the bounce caused either by the kick of a Marker or static charge within the microswitch. The higher the setting, the less likely the Marker is to bounce.

Dwell allows the user to adjust the time the Vlave stays open. The Higher the setting, the longer it will stay open, thus allowing more air to pass through it. Ideally this is something you'll need to adjust if you begin to see dropp off on fast streams of paint or if you just can't seem to achieve consistency or the velocity you desire.

WldWzl · 02-05-2007, 11:56 AM

Curious what operating pressure Bob is recommending for the Marqs. Mine came LPR set at 50, the manual I think says between 70 to 80, others are saying 60. What is the official word, stock parts.

Thanks.

the incubus · 02-05-2007, 12:28 PM

60-65 should be a good starting point and adjust from there as needed, but as with Timmys the higher Pressure will not hurt anything.

the incubus · 02-05-2007, 12:29 PM

Should be an update to this Manual very soon as well, so stay tuned.

WldWzl · 02-05-2007, 03:45 PM

Quote:

Originally Posted by the incubus

60-65 should be a good starting point and adjust from there as needed, but as with Timmys the higher Pressure will not hurt anything.

Thank you, I like keeping the pressure low but just wanted to hear the official word, I would not have even changed it from the 50-55 but I wanted to cure my FSDO. Which setting at 60 did.

the incubus · 02-08-2007, 11:24 PM

Sorry guys... There is an update to this thing but I got the lines through it again so I will have to create a new PDF in the Morning.

I will update you all as soon as we get it posted.

Thanks for your patience!

96 Ls lnteg · 02-08-2007, 11:47 PM

Quote:

Originally Posted by the incubus

Sorry guys... There is an update to this thing but I got the lines through it again so I will have to create a new PDF in the Morning.

I will update you all as soon as we get it posted.

Thanks for your patience!

Its your MACS fault

the incubus · 02-12-2007, 12:06 PM

UPDATE!

Screw & O-ring Charts Added.

Some may be off a smidge on size but I will be finalizing all that withing the week. Just waiting on the Renderings to place the Exploded Views with Parts Lists, but that's pretty much it.

enjoy.

joshisburning · 02-19-2007, 11:23 PM

i have a question about the reg... does the adjustment screw on the bottom of the reg need to be all the way out or all the way in to start off at zero in order to bring the pressure up slowly? i want to give this reg a try on an ion i've built from the ground up and don't want to blow any internals when i air up. thanks

the incubus · 02-19-2007, 11:34 PM

Start off with it out and then turn it IN to UP the pressure.

joshisburning · 02-21-2007, 12:09 AM

thanks, incubus

the incubus · 02-21-2007, 11:57 PM

Hey Guys an updated version is now up. Nice & Clean NEW COVER!

Hope you all like it.

wowmas · 02-27-2007, 10:24 AM

How do i know what is my working pressure?

the incubus · 02-27-2007, 10:46 AM

Screwing in your Brass Adjustment knob to the point where all the threads are inside generally leaves you in the pressure range of around 60psi give or take.

What I did before I had the Pressure Guage was to screw it in like stated above and then give it 1/4 more. That left me more towards the 65-67-ish range and I had no issues.

A pressure of 70psi would work just fine without adding any kick and will prevent any likelyhood of developing FSDO.

Snowmansam8 · 02-27-2007, 09:31 PM

will a lower pressure by around 5-8psi show any noticible difference in efficiency?

the incubus · 02-27-2007, 10:08 PM

If you are at or around the cut-off for optimum performance, then YES.

THere really is NO NEED to run it at an extreme minimum LPR setting. Rather than risk experiencing shoot down during a match, why not just keep it up a touch and to ensure you don't end up starving the Marker for air?

It adds no additional kick if that's what you're worried about and it will not affect efficiency in the least.

wowmas · 03-13-2007, 06:19 PM

Quote:

Originally Posted by the incubus

Screwing in your Brass Adjustment knob to the point where all the threads are inside generally leaves you in the pressure range of around 60psi give or take.

What I did before I had the Pressure Guage was to screw it in like stated above and then give it 1/4 more. That left me more towards the 65-67-ish range and I had no issues.

A pressure of 70psi would work just fine without adding any kick and will prevent any likelyhood of developing FSDO.

any diagram?

the incubus · 03-15-2007, 11:37 PM

UPDATE!

Regulators Parts List Now Added. The rest will follow so I can wrap this baby up rather sooner than later.

ROB.

**Lurker27** · 04-03-2007, 04:33 PM

"Detrimental" in the tip on page 20 should be "critical", as proper orientation is important, but not in a bad way.