Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 01-03-2007, 09:35 AM #1
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest
Lightbulb Official Steps for Shego



First: You need either a shocker solenoid( requires disordering the upper board from PARKER solenoid, or pulling the board from the HUMPHREY SOLENOID). After the board is removed you must solder wires to the leads on the solenoid (do not solder them going down, but run them down the length of the solenoid it self then find correct nylon connector, OR if you wish you can use a ego solenoid. Then you will need an ego frame, trigger, electronics for ego frame, shocker body old frame, measuring device, sharpie, and either a mill or dremel with assorted end mills.

After you have the wires on the shocker solenoid, I took some epoxy and put it on the wires and leads so they do not move.


If you are using an ego solenoid, go to step four
.

Second: Mount the solenoid to the manifold so it is on the body. You must measure the length of the already existing space for the solenoid. Then measure the length of you solenoid and find out the difference. This is were the sharpie comes in. Take the marker, and with the measurements you took, mark off were the main cutting needs to be done. REMEMBER: measure twice, cut once!

Third: Place the frame in a devise to hold it steady (I used a wood cutting bench). Now with your cutting device, slowly star to remove metal from within the frame. Remember not to get to close to he sides were the grips are held. If you need to make changes to the measurements, then do it slowly. After every few minuets, take the solenoid and line it up to make sure you do not have too much room. *NOTE* you will need mill in to the back part of the trigger space to allow enough room for the solenoid, but not to pass through the back.



Fourth: After you have the solenoid in its space within the frame, take your stock frame and line it up next to your ego frame using the solenoid space as a set benchmark. Measure the space from the CENTER of the hole to the very tip of space used for the solenoid. Do this for both the front and back holes that will be used to hold the frame to the body. AGAIN: measure twice, cut once. Then mark off with the sharpie. I suggest if you are not using a true mill that you use a smaller drill bit, and move your way up. Less of a chance of screwing it up.

Fifth: After you have the frame mounted to the body, you can decide to either keep the back portion of the frame on, or cut it off. If you have a ST snatch grip from a ST frame/shocker, and you want to use it then you will have to measure were you want it to sit within the frame. You must cut some of the frame of in the back so that the frame will allow the snatch to get to the screw. After you have that, you will have to mill the inside of the snatch grip to allow it to reach to the back screw that holed the frame to the body. Once you have the snatch grip milled on the inside, you must mill the part that will sit within the frame down so it is level.



Sixth: You can either cut the front of the frame to line up to your VA, or can cut it at the front of the trigger guard.

Seventh: Trigger milling is required. You have to cut the very part of the trigger to “about” the first screw that is used as a magnet to pull the trigger to the magnet within the frame. After that is done, you need to carefully mill the back part of the trigger around the screw that holds it in( stock or any trigger that has a screw to hold the pin down) as well as the shaft that is used to hold the main trigger to the swivel point.



Eighth: If using a shocker solenoid, you will have to mill a little end grove in the end cap of the solenoid. This is so you do not have to take any more than you have to from the trigger.

Ninth: Clean off all parts that came in contact with parts that were milled. Make sure you do a good job, you don’t want little burs or other **** in the gun.

Tenth: Get out and ball it up!

Tools I used to do it.



As you can see I did a little more in depth milling for a unique look, you can do any thing you want to. this is just the basics


Please only post in regards or question for shegoing.
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 01-03-2007, 09:37 AM #2
Aria
ODAAT
 
Aria's Avatar
 
Join Date: Jul 2004
Location: Fort Wayne , IN
 has been a member for 10 years
Aria helped look for balloons
Aria supports Team VICIOUS
Very Nice.
__________________
Es Kay'
Aria is offline   Reply With Quote
Old 01-03-2007, 04:08 PM #3
bigdaddyreg
Im doing 10 in the nation
 
bigdaddyreg's Avatar
 
Join Date: Aug 2004
Location: Arizona
bigdaddyreg is a Supporting Member
bigdaddyreg supports Cereal Killerz 2
bigdaddyreg donated to help Peyton Trent
bigdaddyreg owns a Planet Eclipse Etek
bigdaddyreg supports our troops
bigdaddyreg is attending Decay of Nations VI
good work, and good documentation
__________________
My Feedback 75 the old way


I have expired infractions that are older than most members of PBNation
bigdaddyreg is offline   Reply With Quote
Old 01-04-2007, 05:21 PM #4
angrysasquatch
 
 
Join Date: Aug 2005
Location: Canada
That thing'll look soo nice once its anno'd. You are annoing it, right? One thing that'll make it look better after anno, is make that hybrid bolt guide less hideous with the dremel then send it in. Its nice to see someone who thinks and puts out the time before he makes a new thread. Good job on it.
angrysasquatch is offline   Reply With Quote
Old 01-04-2007, 05:23 PM #5
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest
look at top pic. It has been ano'ed.
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-04-2007, 06:13 PM #6
PaintballerFourLife
PB4LIndustries
 
PaintballerFourLife's Avatar
 
Join Date: Sep 2005
Location: [714] SoCal
Annual Supporting Member
PaintballerFourLife is a Supporting Member
PaintballerFourLife plays in the USPL
PaintballerFourLife plays in the PSP
PaintballerFourLife is an NCPA player
PaintballerFourLife plays in the APPA D3 division
PaintballerFourLife is one of the top 100 posters on PbNation
PaintballerFourLife is Boss
Quote:
Originally Posted by StrangeBalla55 View Post
look at top pic. It has been ano'ed.
The top pic doesnt work.
PaintballerFourLife is offline   Reply With Quote
Old 01-04-2007, 06:16 PM #7
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest
really? It does for me
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-04-2007, 06:50 PM #8
egokid1994
 
 
egokid1994's Avatar
 
Join Date: Dec 2006
it works for u because its your pic and it works for me too
__________________
Do your part.
Fold for a Cure Join Team pbnation. Team # 46692
EgoSL74 Aurora with Purple Parts
www.bradywilliamsphoto.com
Editor:www.gadgetous.com
egokid1994 is offline   Reply With Quote
Old 01-04-2007, 08:52 PM #9
angrysasquatch
 
 
Join Date: Aug 2005
Location: Canada
doesn't work for me either. The ones for the how-to do, tho.
angrysasquatch is offline   Reply With Quote
Old 01-04-2007, 08:58 PM #10
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest

Rehosted it.
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-11-2007, 03:53 PM #11
ebayunderground
 
 
Join Date: Mar 2006
still didn't work
ebayunderground is offline   Reply With Quote
Old 01-11-2007, 03:57 PM #12
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest


It does now
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-11-2007, 05:37 PM #13
crass
 
 
crass's Avatar
 
Join Date: Aug 2006
nope still didnt work
crass is offline   Reply With Quote
Old 01-11-2007, 05:42 PM #14
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest
you guys dont know what your missing.
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-12-2007, 04:50 PM #15
superskater1991
i dont get it...
 
superskater1991's Avatar
 
Join Date: Dec 2005
Location: that one place...
the pics host adress is

http://i8.photobucket.com/albums/a35...la55/*****.jpg

I dont know if the stars are supposed to be there, but can one of you who can see it right click then copy&paste the source for the rest of us?


Btw, Very nice job, well documented, and clean considering the arsenal of tools you have been blessed with lol
__________________
Ice X-treme Paintball
www.ixp07.com
BLACK ICE
WHY CONFORM


http://www.zdspb.com/media/quest/wide1.jpg
superskater1991 is offline   Reply With Quote
Old 01-12-2007, 04:58 PM #16
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest






better?
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-12-2007, 05:05 PM #17
happydude_911
 
 
Join Date: Jan 2005
Location: *905*
They're all working for me. Very good instructions
__________________
Bumtown Hustlers
My Feedback
happydude_911 is offline   Reply With Quote
Old 01-12-2007, 05:14 PM #18
superskater1991
i dont get it...
 
superskater1991's Avatar
 
Join Date: Dec 2005
Location: that one place...
Dang that turned out really nice man, props!
__________________
Ice X-treme Paintball
www.ixp07.com
BLACK ICE
WHY CONFORM


http://www.zdspb.com/media/quest/wide1.jpg
superskater1991 is offline   Reply With Quote
Old 01-12-2007, 07:39 PM #19
cockerstar
\(_o)/
 
cockerstar's Avatar
 
Join Date: Dec 2004
Location: Kennewick, WA
eyes?
__________________
.
1971 240Z, 1969 Camaro, 1972 240Z, 1973 240Z, 1979 280ZX


Prairie: "Don't respect me: I still rape little children."
R.I.P. Kylie Nichole Rock July 6th 1990 - August 30th 2006
XxHat3d1xX: "I don't even need the Rambo knife or Camo Paint, the sight of me in a loin cloth can kill any animal known to man."
trust
cockerstar is offline   Reply With Quote
Old 01-12-2007, 07:44 PM #20
StrangeBalla55
bamcis
 
StrangeBalla55's Avatar
 
Join Date: Dec 2004
Location: Stuttgart
StrangeBalla55 donated to help Peyton Trent
StrangeBalla55 supports Sherwood Forest
There is now. Not at the time of pics. I am using timmy quick discounts.
__________________
SOG


DEEP SEA
StrangeBalla55 is offline   Reply With Quote
Old 01-12-2007, 07:55 PM #21
happydude_911
 
 
Join Date: Jan 2005
Location: *905*
Do the timmy eyes plug into the Ego board without any modifications?
__________________
Bumtown Hustlers
My Feedback
happydude_911 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump