[IMPY~[e^A]]

Hey guys,

Well I finally got off my lazy butt and I just wanted to help out all the Legend owners and the soon to be owners. First off let me just say that I was so surprised how little maintenance these guns need and how simple it is to break the gun down.

Remeber I got a Prototype version of the Legends. Your guns will have cleaner milling, as well as different eye covers and eyes and other small changes..

Tools Needed:
Allen Keys
Lube ( Slick Honey, Dow 33, etc. )
Q-Tips
Paper Towels



First I am going to show you how to remove your Ram and lube the 1 moving o-ring found in the Legend.

Remove the back frame screw.



Remove the bolt. Clean off all debris on the bolt with a towel. You do NOT needs to lube the bolt so just set it aside for now.



Now using a small allen key push the ram housing back through the slot under the bolt.



Out pops the ram housing.







Now simply separate the Ram (silver part) from the Ram housing (black part).



Clean out the Ram housing ( black part ) with your Q-tip.



Now lubricate this o-ring. This is the only moving o-ring in your Legend.



Now remove the main spring from the Legend ( It should just slide right out ). Clean the spring if needed.



The spring goes back onto the Ram as pictured.



Insert the Ram assembly back into the gun. It helps to put a little bit of lube on the 3 o-ring on the outside of the ram housing to let it slide in easier. Make sure the holes on the Ram housing are facing down toward the bottom of the body.



Now screw the back frame screw back onto the gun. Make sure you push the Ram housing all the way in while tightening the rear frame screw as shown.



Now you can put your bolt back into the gun.

Eyes & Detent cleaning.

Remove your eye covers.



Remove the Detents from the slot. Clean from all debris.



Quote from manual: “Do not pull on the eye wires. Use a small pick or screwdriver to pop the eyes out of this slot. If necessary you can use a small Allen Wrench to push the eye out from inside the breech of the gun.”



Put the eyes back in their spot. Put the detents back in their spot then put the eye covers back on.

[IMPY~[e^A]]

Exhaust Valve Removal

Remove your grips. Then unplug your solenoid harness.



CAREFULLY REMOVE YOUR TRIGGER FRAME, DO NOT PULL THE FRAME OF COMPLETELY. WHEN YOU CAN SEE THE EYE WIRES UNPLUG THEM FIRST.




This is what things should look like after frame removal.



Remove the set screw holding in the front block.



Remove the front block.



The Exhaust Valve Assembly should just fall out. Clean off any debris.



To reassemble just do everything backwards.

adaM.

[drefish99]

Lets keep this informational for usage for Legend owners. If you have anything to say about design or cost please post it elsewhere.

[EclipseBaller]

ShoOtxKilLxWin- take the other grip side off. the top screw is holding the solenoid in.

naughtydawg63- sucks that they let it go through like that but little things can be over seen. contact infinity im sure they'll send one right out.

[ShoOtxKilLxWin]

Originally Posted by EclipseBaller

ShoOtxKilLxWin- take the other grip side off. the top screw is holding the solenoid in.

naughtydawg63- sucks that they let it go through like that but little things can be over seen. contact infinity im sure they'll send one right out.

ooo thx

[T-Ion]

http://www.*************.org/video/1...d3013aa71c.htm

vid on how to do soem fo the stuff

[Rithem]

Is there a way to detach the hose before pulling the front block off?

[angelman092 (Banned)]

will slick-oleum work for lubing the ram ??? pm me with the answer please

[taylordtaylord]

any recomendations on lube?

[SoCalSmErf]

just use sleek/dow

[taylordtaylord]

k, sorry to keep asking all these questions but all i gotta do is lube the one oring on the ram with some DOW 33?

[Rithem]

Yup

[naughtydawg63]

my front block woulndnt come off w/o takin off the hose. i dont know how to take off the hose so i just stopped any advice?

[deadlymystery]

when you try to take the front block off it will be difficult and it will seem like your not doing it right...so you can keep pulling without damaging anything...however if you want to take the hose off...at the base of the hose where it attaches to the front block,there is a thing where you can put a small wrench...just unscrew it with a wrench and it will come off

[naughtydawg63]

ok thakns ill go try that out.

[b_ron]

the manual said to use oil to lube the gun not grease
isnt dow a grease?

[~SnOwBaWls~]

Originally Posted by b_ron

the manual said to use oil to lube the gun not grease
isnt dow a grease?

This is a old thread and Infinity found out not to long ago that grease.lubs clogs your gat

[b_ron]

alright cool

also, the pic of the ram on this thread is the old one right? because i just got my legend yesterday and it looks a little different.. like thinner

[xpb boy (Banned)]

yeah he has/had the old ram

[Nepb2]

Originally Posted by ~SnOwBaWls~

This is a old thread and Infinity found out not to long ago that grease.lubs clogs your gat

so are you saying it isnt a good idea to use dow?

[Johnny5072]

Tri-flow is now used and recommended by Infinity.