three shots, then eyes off WTF! HELP

[CgotNerve59]

Ok, so i turn my quest on, i turn my hopper on, i turn the air on, then i let it rip, midstream i break, i finally figured out why, my hopper isnt keepin up and the eyes are turning off after the third shot, EVERYtime. please help me.

Thanks,
Chris

[ikey]

im guessing the baord is WAS? it is was programming that does that. when teh board detects a malfuncion, it gives you three shots. after 3 shots, WAS takes the gun out of eye mode and into manual.

funny thing is, generally when that happens, the gun doesnt shoot because of an issue, and on teh 3rd shot of not fireing it switches. ive nenver heard of WAS doing that with the gun still firing.

i dunno, check your eyes. change battery, clean eyes. if nessesary try resetting baord?

[CgotNerve59]

no batteries fine, it is the was, it just shuts the eyes off, everytime, even if there is no jam or nething, the eyes are clean

[CgotNerve59]

all my settings are stock exept for lpr, so if you could tell me how to reset my board, it would be much appreciated

[ikey]

well im not sure id its the same on every WAS baord, but i do know that in my freind ceptor and my old impulse, while in programming mode (any mode or blinking light it doesnt matter) hold down the trigger for like 6-10 seconds and sooner or later you should see a red light blink rapidly.

[CgotNerve59]

it didnt work, nobody can help me?

[egosOWNshockers]

I had the same problem. Its your hopper, mine did that the first day I got it. Rip on it, then hopper goes to slow (or something, jams, etc.) and after like 3 seconds, the eyes turn off and dry fires. I have a empire (sound activated) so it finally goes once it dryfires. So then start ripping on it again and since the eyes are off it chops like crazy. Just do drop tests on your hopper, put in new batteries and make sure its not messed up and is going at least 15bps.
Hope it helps.

[CgotNerve59]

im pretty sure my hoppers fine, even if its not, thats what the fuckin eyes are supposed to be fore, lol, to make sure the gun doesnt go faster than the hopper, so why even have em if they are gonna turn off?

[GnaRkiLLK5]

put it on eye mode 3

[LU_aDaK]

Make sure you reset your settings...eye delay could be all fudged up. Also what loader are you using...not that it should matter but I know I had trouble with a Emp B with my gen 1 quest because it did not kick. Reset the settings and use a new battery, even if your battery is new, hell its worth a try, otherwise I would be sure to check the wire connections between eyes and the board.

[evileric77]

When you turn the gun on do the lights go from solid yellow to blinking green? To reset your board back to default settings you need to enter programming mode then hold the trigger for 6 seconds. You should see the LED change from solid red, to flashing red and then back to solid red. Once you do that turn the gun off then back on again and try testing the eyes. The gun should be blinking green twice per second once the board has booted after a factory reset. If the LED is flickering green and you don't have anything in the breech then you have an eye problem.

EDIT:GnaRkiLLK5 - there is no eye mode 3.

[CgotNerve59]

When you turn the gun on do the lights go from solid yellow to blinking green? To reset your board back to default settings you need to enter programming mode then hold the trigger for 6 seconds. You should see the LED change from solid red, to flashing red and then back to solid red. Once you do that turn the gun off then back on again and try testing the eyes. The gun should be blinking green twice per second once the board has booted after a factory reset. If the LED is flickering green and you don't have anything in the breech then you have an eye problem.

EDIT:GnaRkiLLK5 - there is no eye mode 3.
yes it goes from solid yellow, so blinkin green, not flickering. the finger in breech one shot finger out back in one shot finger out then back in one shot, ten it goes to eyes off.... WTF!!!! I reset it still nuthin im fuckin PISSED

[evileric77]

Sounds kinda boardish. Sorry bro.

[cjm555]

i had the same problem. when you just put your finger in the breach it doesnt work. im guessing its expecting it to cycle and it says something is wrong. what i did it reset my board, clean the eyes, new battery, and turned the eye sensitivity up to 15 and it works fine

[Physcojosh]

Call Up Fep, and ask for them to help ya.


meh may sound like an ass.. But Buy a new Board .. :tdown: to Was Anyway...

[CgotNerve59]

i kno i hate the was board, but how do i turn the eye sensitivity up?

[Physcojosh]

Do you Have AIm or Msn? Hit me up and i will help ya

[rinso]

I know that if it doesn't detect the bolt movement it'll do that. If I do exactly what you did with your finger mine does the same thing, but when it's actually cycling with air and paint it doesn't do that. If it's doing that with paint and air though, your board might be messed up.

[cjm555]

i believe the eye sensitivity color is teal?

[rinso]

it's in the ultimate sticky.

[Physcojosh]

I fixed it :P

[rinso]

:tup:

[cjm555]

just curious...what did the problem end up being?

[CgotNerve59]

in programming mode, yellow the eye proggramming, in 3 after 3 shots if the ball doesnt drop as fast as the eye reset, it will turn them off thinking there is a jam or break and cap the ROF. but in mode 2, this does not happen, there is no eye reset,

[mike13sk8r]

I have the same problem but I put my eye mode on 1 I think, the setting where it fires up to your personally set bps cap, and then it worked fine, but i can still never shoot in uncapped mode or it turns the eyes off.

[CgotNerve59]

yup, you have to up the BIP or wutever, they ye reset time, but it lowers the ROF. but its fast enough as is if you set it capped at like 16, you dont need more than that, i mean, common, o and its eye mode 2, 1 is no eyes at all EVVER, and 3 is the uncapped

[Physcojosh]

yellow 1= Bypass mode <No eyes> Cap at 13 Bps
yellow 2= eyemode 1 , goes by Max Rof
yellow 3= eyemiode 2 Unlimted Rof
yellow 4= Demo mode.. like Bypass, but NO cap <unlimited Rof>

[CgotNerve59]

sounds right, yellow four is like the ego Training mode

[impypballr47]

you have the eye mode in the stock settings. change the eye mode to eye mode 2

[noobtacular]

I've got the same problem on my Quest... It's a Gen 1, which has a different board then the Gen 3 :s

[GnaRkiLLK5]

When you turn the gun on do the lights go from solid yellow to blinking green? To reset your board back to default settings you need to enter programming mode then hold the trigger for 6 seconds. You should see the LED change from solid red, to flashing red and then back to solid red. Once you do that turn the gun off then back on again and try testing the eyes. The gun should be blinking green twice per second once the board has booted after a factory reset. If the LED is flickering green and you don't have anything in the breech then you have an eye problem.

EDIT:GnaRkiLLK5 - there is no eye mode 3.

dammit, I meant the 3rd click, so it would be eye mode 2
I meant 1 is dryfire, 2 is eye mode 1, and 3 is eye mode 2.

my bad

[Campoe13]

clean your eyes and your gun.